Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
In order to send an SMS in PDU mode, I need a Service Center Address. Normally, you can find it via AT+CSCA, but this does not seem to be supported on modem firmware v1.0...
I have a central device (nRF52832/Soft device s132) that connects to two peripherals. Both peripherals send data to the central via NUS. I have incorporated the required changes...
hi guys , I'm trying to use the ble mesh protocoll for my master thesis. I need to send a message always when an interrupt on a gpio pin occur.
there's a problem beetwen...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
chip: 52832 . sdk 12.3\examples\ble_central\ble_app_uart_c\pca10040\s132,
i use this example to scan ble advistisment, i want to write some date to flash, i use flash_word_write...
Hi
I am doing a mesh application with :
--SOC:52832;
--with an AT Command Module connected UART;
--Mesh SDK :3.2;
--SDK 15.3;
in order to manage call backs from...
I built ...\examples\dfu\bootloader_secure\secure_dfu.eww ,pass,then when download to PCA10040 board to debug,but it show error" ELF/DWARF Error: Unsupported .debug_info format...
I am running custom firmware on a custom board using an nRF52832 chip. I have encountered an issue after migrating my project from SDK 14.2 to SDK 15.3. The issue is that...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
Since I migrated from SDK 13 to SDK 15.3 I can not see anymore print of NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR and so on, on segger Jlink Viewer.
I have tried...
Are the following arguments correct?
data_rate <RADIO_MODE_MODE_Ble_1Mbit> or <RADIO_MODE_MODE_Ble_2Mbit> and so on.
output_power <RADIO_TXPOWER_TXPOWER_Pos4dBm> and...
Hello,
We are using the nRF52832 and 2G(GSM/GPRS) module to build up one IoT product. We got a disconnect between nRF52832 with other master instance(mobile phone APPs)...
Using Softdevice s140 v6.1.0 nRF5 SDK v15.2.0
I am trying to write to the flash, here are my read and write functions:
Two problems:
The write function does not...
Hi,
I've added an instance of the Generic Power OnOff Setup Server to an element and I can see it and all the models that it extends, i.e. (Power OnOff Server, DTT Server...
