Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear,
I am using ncs_v1.0.0_rc4, and got the FW mfw-nrf9160-1.0.0-25-rc2.prealpha from . I want to update this FW
I tried to use nRF Connect v3.0.0 Programmer
/Cellular...
I am developing software for the nRF52. As recommended by many recent posts here in the Developer Zone, I have upgraded to SDK 11. I am working on an application for a battery...
Hi, I would like to share some valuable information regarding the BLE DFU (secure bootloader) and a MESH application which uses persistent storage for provisioning data. I...
Dear all,
I'm using two nRF52 Preview DK boards with the SoC nRF52832 and I'am testing the light switch example with sdk 3.1.0.
For my application I need one client...
MY CHIP is NRF52840, EVB is PCA10056
SDK: nRF5_SDK_15.0.0_a53641a
bootloader use secure DFU example: \nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_ble...
Hi,
I found your PDM Working Example. However I wonder what to make of the data I get.
What is the CONFIG_PDM_BUFFER_SIZE_SAMPLES for? Do I get 16Bit Bit-Schemes from...
I am using SDK12.3.0 + SoftDevice S130 in nRF51 DK.
I create 4 channel PWM (+ppi) in timer1 & timer2, because I know timer0 is used by Softdevice, RTC1 by App_timer.
My...
This is more of a Segger question than an Nordic question, but it seems enough folks here use J-Link tools that I could ask here.
RTT Logger and RTT Viewer doesn't log the...
Hi Nordic community
I want only send data using ble app_uart example with out receiving anything. So i tried to send the data that i received from my device to my android...
I am working on the safety-critical system, I have, ON and OFF function, the entire system using UART communication. In which I am using the nrf_queue() and push the data...
Hello everyone,
I have been using nRF52832 module from Raytac ( link ) for my circuit and I got a trouble with sending advertising packages to other master devices. I installed...
Hi,
I am trying to merge working code that places the microcontroller in system_off when a switch connected to pin 16 is opened. It then wakes up the micro controller when...
Hi, I am working on application where I need to store some bigger files. I chose to use sdcard, but I get weird behaviour. Some sd cards, this looks like totaly random ones...
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
