I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I have set up an nrf cloud and can control the led on pca10056 using the nrfcloud so configuring the gpio(pin no 7(Port P0.7))is becoming a problem.Can u provide me with a...
Hello,
I bought a nordic/wellcore ibeacon (nrf51822) to experiment. I want to enable all the features and would like to know what value to assign to the temparature enable...
Hello, i am using SDK12.2.0 and SD s130 on a nRF51822 (AC) and i am trying to add an external interrupt on a pin in the cscs ble_peripheral example. The code i am using (and...
Hi
We are using sdk version 12.2.0 and trying to change it to sdk 14.0.0. However, when I measured the power while converting the code, ppk confirmed that the sdk 14.0...
Hi all,
I'm using SD S132 v5.0.0 with SDK 14.0.
I'm testing now the BL buttonless DFU (and later the SD buttonless DFU) after working well with the app buttonless DFU...
I've implemented monitor mode debugging as described here and it works great. When I get a hard fault, it doesn't break in the IDE anymore. So it appears to be running fine...
I can connect the kit to the nrf cloud and even add the device to the gateway but i cannot switch on and off the leds.Where is the source code for the nrfcloud example?I cannot...
Hi all,
I recently encounter this strange issue that I couldn't understand. My code works perfectly fine during debugging on all 52832 chips, but freezes without response...
For nrf52832, I use pstorage to set 254 blocks with 20 byte of each block, that will use near 5 pages.
now I fail to clear data all block together. pstorage_clear( &block_base_handle...
Using an nRF52832 with SDK 14.0.0, S132 SoftDevice
We are able to connect to the device with an iOS/Android phone just fine.
Upon disconnecting, a second phone is not...
Hi,
I'm trying using AES ECB encryption of peripheral drivers on development board with nRF52832 and PCA10040.
I inserted the following code before main loop of ble_app_uart...
i have a particular automotive tuning application where i have to deal with ignition and fuel injection timing (old stuff in the new e-mobility time)
here are some loose...
I'm a beginner to programming nRF devices in C, trying to graduate from Arduino (i.e. kindergarten).
I've installed Segger Embedded Studio and can compile and run SDK examples...
