Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi all,
I'm having a bit of trouble figuring out why my project using the RedBearLab BLE Nano board is not working. I'm using the NRF51822 as the hub in a star network...
Hello,
I would like to implement a Vendor Specified Interface Class for use with libusb on the nRF52840 USB.
There are examples of HID, CDC, Audio, etc. But it is not...
Hello,
I am trying to get a BLE peripheral with a single service containing a single custom read-write characteristic.
Unfortunately, any time I initiate a connection...
When debugging a project from here
devzone.nordicsemi.com/.../ (the ready code from github)
Segger Embedded Studio shows err_code sybol not found message in Watch winow...
Hi all,
Is it possible to hide a Service during advertising?
And show it after the connection?
If yes, how?
My configuration:
nrf52832 microcontroller
Softdevice...
I would like to synchronize my warning lamps with the advertisment of a master device.
The master is the advertiser as peripheral device. once every second.
The slaves...
Hai,
We are trying to implement BLE HID Keyboard application using NRF51822. but we are facing the below issues with a windows 10 system acting as the central:
when...
I am considering nRF51840 chip to use in my project, I have found good examples for it, but I still have a question if there is a special method to establish new services...
Hi,
I know that this is a known issue, but I'm seeing caching issues often with iOS.
I'm using S132 v5.0.0, SDK 14.0 against custom application with iOS DFU SDK and often...
Hi，guys. I have a problem when dealing with NRF52's SAADC using nRF5_SDK_13.0.0_04a0bfd. The problem is after downloading and run the program using JLink, everything works...
I purchased the nRF52840-PDK the other day and when it came in today Booted it up and it worked fine. I went to load the example nrf52840_xxaa_side_header.hex from the github...
It worked before when I connected my nRF51 board to my windows 7 computer. The green light is on.
But today when I connect them the light is blinking rapidly and there is...
Plugged in board to Win 10 pc that was working properly in past. Start NRF tools and get error.....
ERROR Unable to read connectivity firmware version: Unable to get version...
