after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am trying to print ble device names around my board by scanning and i am able to print some devices and i am unable to print other device names even though they are...
Hi. We recently upgraded from SDK13 to SDK14. All was well until we integrated the bootloader. We are using Laird's BL652. We updated the bootloader's config to use NRF_CLOCK_LF_SRC_RC...
Hello All,
I am new to this area and i am just starting my development for BLE.
i am planning to use nRF52832 . I want to know that if i am planning to make night lamp...
Hey,
I'm new to the Nordic Semiconductors and wanted to get started out trying to learn about Bluetooth Mesh.
I've been reading a lot of posts and trying to get some...
------------ EDIT Sep-21-2017 ----------------
I was able to work around the issue by trying on a Linux distribution. Here is a written guide to the package install and...
Hi,
I have successfully connected an MCP3004 to the nRF52832 and can assign the ADC channel 0 output to a characteristic value. Works beautifully.
However, there are...
Hello,
I would like to know what are possibilities for low power in a central device on nRF52 chip.
I need to be in BLe connection mode, and be able to receive notification...
I'm trying to figure out if the NRF51822 is capable of performing the tasks I need for my project. I need to be able to do the following
4x PWM at ~2kHz
4x Analog read...
I am building a Bluetooth Mesh project and when trying to make a custom Makefile for the Mesh Light Control Example , but when compiling the project i get this error:
Compiling...
!!! (Distributor is unknown to me, but I can get it if needed)
Hello,
We are developing a BLE enabled device to operate on iOS and Android phones.
The nRF52832 chip...
Hi friends,
I'm using a NRF51 IC with this 4.0BLE Modul PTR5518 and i have big problems with Range. As a protocoll i use gazell.
In air it is possible do get some correct...
Hello,
I am currently trying to make an MSD RAM disk with nrf52840 nRF5_SDK_14.0.0 with O0 optimization level. And had no success. For some reason in Keil example O3 is...
Hello every one,
So after I made my 3rd party NRF52832 board and flashed softdevice S132 with arduin ide and ST link V2 I'd like to migrate to something more serious in...
Hi,
Do you know how to make the nodes in the Mesh send back the data to the main device?
For example, a node is a sensor that gets a new value and now needs to send the...
