after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I'm interested in the nRF5 SDK for AirFuel .
I have received a task to replace parts in a product which formerly used wireless charging and the CSR BLE chip.
I think...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hello everyone,
Lately I have been struggling while trying to run "BLE Advertising, a beginner's tutorial". My hardware consists of NRF51822 and PCA1000 dongle. I use SDK_11...
I am working through the TWIS Slave and TWI Master mode drivers Example using SDK 12 with the nRF52832 PCA10040 board and having issues. I am using Minicom through the terminal...
I want to use the last page of codespace for storing a single 32 bit word of non volatile data. I am failing so far and I think I just don't understand the page numbering...
Hello everybody
I am working with the Raytac BLE Module "MDBT40", which is based on nrf51822.
And I am testing example project "ble_app_uart" in the SDK6.1.0 now.
...
I would like to confirm my understanding of Problem sending 6 bytes to multiple services using sd_ble_gatts_hvx
I use nrf52832 sdk13.0.0
BLE SPI is master. I dropped...
Hello,
I connected the nrf module to jlink as described:
• vdd(nrf)-----3.3V
• gnd(nrf)-----gnd
• SDO(nrf)-----SWDIO(jlink)
• SCLK(nrf)-----SWCLK(jlink)
• 3.3V...
I've run into some interesting behaviour in my code and wanted to see if anyone can clarify for me. It seems as though the SPIS module doesn't set the MISO pin as high impedance...
Hello,
I built a simple I2C application for the LMP91000 and I was successfully able to configure it to read the status register.
However, I tested to see if I could...
Hi,
I used to use an imitated Jlink debugger to program/debug my target board(one Nrf51822 on it)
There are pins connection between them,it works just fine.
Now I...
I aslo read other question about sd_ble_uuid_encode .
But my problem is different from it.
I use nrf52832 and DK board.
I made my application from ble-app-template...
