after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I am a little bit confused when reading in NRF52 spec that a NVM page is 4KB while block size is 512B. Usually an NVM memory is composed of block made of pages,...
Hi,
I am testing github.com/.../nRF52-fds-example
I am on nrf52832 with sdk 12.2.0 .
I can't seem to make it work.
What i have done:
Separated FDS stuff to separate...
Hi all,
I am trying use the SAADC in blocking mode inside a RTC I am currently using
The issues comes from the example
saadc_blocking_simple
the ADC always give...
I guess this has been mentioned/asked before but you should really do something to enforce the full chip part-numbers to be listed at distributors.
For example, for an...
(Maybe this isn't an ideal place for issues with your web site, but I could see no better one.)
There is a technical non-conformance in your nordicsemi.com domain. In practice...
I've been testing my application and am having an issue opening MasterEmulator sometimes. I need to reseat the nfr51 dongle to clear out the errors I am seeing below. Any...
Hi,
I get error NRF_ERROR_INVALID_PARAM or error 0x12 from sd_ble_gap_connect in central.
I even changed peer_addr.type to 0 (BLE_GAP_ADDR_TYPE_PUBLIC).
When scanning find...
Hi, I'm trying to use an MDBT40 based board as a sniffer using the NRF sniffer firmware. I'm guessing I just need UART -> USB to talk to the chip, so I've hooked it up to...
Hi,
I am trying to figure out the best way to save power on the nrf52. I need to connect with ble about two times per day. The ble should 'woken up' by an accelerator ...
How can I flash both the dfu bootloader and an application, and have the application run after the flash?
As soon as I flash the bootloader, it kicks in doesn't fire the...
Hi,
While updating from the antique NRF51 SDK8.1.0 to the newer SDK 12.2.0, I came across a problem: Gcc crashed with:
c:\users\elm\documents\nordic\nrf5_sdk_12.2.0_f012efa...
Hi all,
i have some problem to use Timer0_IrQ.
i start first with a program that use a softdevice. After i want change this project with another that don't use it.
...
Hi,
I would like to know if the NRF51822 (Just the NRF board, not the BLE Nano) comes already prepared to be programmed or if it needs some modification. I want to program...
Hi,
I have successfully implemented the UART over BLE. Now I'm trying to implement the HID over GATT for my nrf8001 device. What I'm trying to achieve is lower connection...
Hello,
I am attempting to setup a SPIS interface, and I am continuously getting 0x00 inside my RX buffer. I am varying the length of TX from the SPI master, and seeing...
