after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I'm trying to use the SPI example from the SDK 11 to comunicate with a MPU accelerometer.
The first time it works well, but then the clock send only 8 peak, so the...
FIrst timer with the nordic.. so i could use some help.
i've tried my code on the eval kit and it worked fine. On my custom board (has external 16MHz crystal www.digikey...
I've come across a couple of products that shows up as both classic and BLE. But when connecting to these products via nRF Connect or inspecting the traffic, I can't seem...
From reading the reference manual, product specification as well as searching the developer zone: here and here . Is it correct that the AVDD pin supply's ONLY the radio....
I have a strange problem with the secure bootloader.
After a succsessful DFU update of firmware, the firmware starts, but resets after a short while (about a second). ...
Hi,
While I'm Flashing LED Blinking Example in nRF51822 Ek using Keil uVision 5 along with SDK v12.2.0 , Program is uploaded but LED is Continuously glowing without blinking...
Hi
I have been trying to make a dual bank serial dfu bootloader with security features for nrf51822 (board 10028), but seems the UART/HCI dfu support is missing in SDK...
Hi,
I am having some trouble getting my design into low power.
I have a BLE central application using an nRF51822. I am using the power on sleep mode by calling sd_app_evt_wait...
Hi Nordic,
I have an application that perfectly runs in the nrf51DK but that does not work in my custom board. In my custom board everything else works (i2c, leds lighting...
I have a nRF51822 development dongle. I followed by the instruction and installed the USB friver, nRFGo Studio and Wireshark. All these software are installed a Win7(64bit...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
What is the best way to go about implementing secure reads/writes to the NRF52 NFC tag? I noticed there didn't seem to be any built in security functionality in those areas...
I am attempting to use nrf_drv_adc.h in a project where I am splitting up my methods across many C files and, to my surprise, nrf_drv_adc.h does not have any include guards...
