after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I wrote a program that uses ESB communication between two nodes. On both sides I use the same ESB configuration and the same ESB init function, the difference is only...
Hello,
Environment: nRF51DK + SDK8
We've developed the beacon application but the advertising interval is set to 5 seconds. The beacon can be discovered by nRF Connect...
I have searched here on the DevZone, and also around the web, and don't see this issue mentioned elsewhere. I really appreciate any help finding a solution.
I tried following...
Hi All,
I think I noticed a bug in the nRF Connect v1.0 application. The Scan Response data is not shown in the Windows application. When I scan the device with the iPhone...
nRF8001_BLE_UART.txt
I am using an NRF8001 with the ble_uart_project_with_dfu_template and programmed an ATMEGA328P with it. The code works great and I can scan and communicate...
Dear sir,
Can we use 8.08.90 J-LINK EDU for programming of Nrf52832 Chipset.Please also specify its limitation if it has any.
If we cannot use this then please specify...
I'm starting to use Wireshark a little more and sometimes it is not displaying all of a device's manufacturer data. For example on some devices it is not displaying the manufacturer...
hi,
As a ambitious tech lover i bought BLE400 nrf51822 motherboard. I downloaded SDK 11.0, keil and nrfgo. I started programming based on the Nordic developer Zone. I first...
Hi, I try to connect nrf51822 and use example "ble_app_hids_mouse". I can pair this device and I confirmed that "Notify" becomes automatic at that time in Enable.
But, when...
Hello,
I am working with the Enhanced ShockBurst protocoll on a nRF52832.
For synchronization reasons between several nodes I need time stamps in my data packet...
hi, i build a test project to test IAP(in system program) function of nrf24le1. the project just did follow things:
1. setup uart;
2. erase page 30
3. write data "0xaa...
I'm new to nrf8001
I'm trying to understand an existing example.
in this example after sending set up commands generated by nrfgo studio , program sends 9 byte of 0xff command...
I downloaded central and peripheral ble UART and I want to add some function to my code and use some GPIO, I programmed nrf51822 by nrf51422 source code and it worked, but...
