Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
What might be the reason that sd_softdevice_is_enabled fails? I've been programming with the S130 for some time now. And now I am in the process of adapting the bootloader...
For the S310 stack the bootloader does not set a SD_MBR_COMMAND_INIT_SD command. What needs to be done for the S130 ?
#ifndef S310_STACK
sd_mbr_command_t com = {SD_MBR_COMMAND_INIT_SD...
[PLEASE READ THE EDIT FIRST]
So, first of all, I am new to bluethoot development and I am not 100% familiar with all the inner workings of the protocol.
I am trying...
I have looked over the entire site and can not figure out what is needed to change the Smart Beacon Kit firmware and uploaded it to the beacon.
Is there a way to recompile...
Hello ,
I'm working since few days on nRF51 dongle with SofDevice S310 and most things seem to be ok.
But when I follow the System OFF and wake-up sample supplyed on GitHub...
The v3 nrf51822 and nrf51422 power efficiency was improved.
What were the improvements? How much effect should we expect to see in various operating modes. System OFF,...
In the Nordic code at this github example
there is a reference to UICR.CLEN0 .
#define CODE_REGION_1_START 0x00020000 \\
/**< This field should correspond to the size...
What is the main difference between HW controlled TWI master driver and SW controlled TWI master driver?
What is their advantages and disadvantage?
Can they switch between...
I am creating four timers in my application using app_timer.c . All timers work except the timer with ID zero never triggers.( means first timer created does not work all...
I am really struggling to get my ADXL345 SPI code working. Everything works fine on a LPC1768 and all outputs are fine on the nRF51822 Eval board, but there is no activity...
Greetings,
SDK6.1 and Keil V5.12
I try to build the executable for Nordic GitHub project Timeslot Oberver example. I get an error that the handler SWI0_IRQHandler is multiple...
I created a app with s110 V7 and want to program the PCA10006 with this app.
To get thing working, I need to update the softdevice as well (beacon PCA10006 is shipped with...
I am trying to use the latest (s130_nrf51822_0.9.0-1.alpha) S130 and experiencing an issue which was not seen in previous version (s130_nrf51822_0.5.0-1.alpha), this is the...
Hello,
We're interested in measuring the precision of our external crystal, but don't have the equipment to measure off the crystal directly without affecting capacitive...
