Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi, Is it possible to estimate the power consumption cost for sending data based on information provided by the modem?
Note from nRF9160 HardwareVerification Guidelines...
I was trying to connect to NRF52-DK using this Python script:
https://github.com/thomasstenersen/pyrtt-viewer/blob/master/pyrtt-viewer
It runs fine on some machines, but...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
Simon posted in this discussion an example of adding a custom service to the...
Dear Members,
I followed the step on :
https://devzone.nordicsemi.com/f/nordic-q-a/71299/getting-hardfault-error-when-using-ble-lesc-pairing/292979#292979
and I got...
Hi,
I'm developing with 52832 DK. I used 'CONFIG_NFCT_PINS_AS_GPIOS' to config pin9, pin10 as general GPIOs and set pin10 to SPI_MOSI. However the system crash when applying...
Hi,
I am creating a BLE communication device (peripheral) using softdevice S132 (v7.0.1) and SDK 16.0.0 on the nRF52832 microcomputer.
I have implemented the BLE communication...
Hello,
I'm new on Nordic environment, I'm designing a RF module that require low latency to transmit few bytes (less than 10) in less then 10ms from a triggering input...
Hello,
Referencing the specification , the time it takes to complete the COMPARE task upon triggering is not directly outlined.
I would like to have the following function...
Hi,
I've installed VS Code 162.3 on Windows 10 machine via Toolchain Manager. I've also installed nRF Connect extensions for SDK v1.7.1. The build system works under NCS...
We need to know the list of configurations to explore more like the following configurations in proj.conf file
for C++ files we enable following configurations in proj...
I use cli library functions for serial port communication, using macros to define m_cli_uart and m_ m_cli_uart _transport variables, program compilation is no problem, when...
Hello everyone,
I used the Multirole example as base for my code. My target is to make a communication with two NRF52382. I changed the HRS (heart rate servide) to my custom...
Hi,
I am using the PCA10040 DK (v1.1.1) to measure the current consumption in sleep mode and the current is about 200 uA. (3V, DCDC Enable)
Following is the code, it...
I'm new to the nRF Connect software and I'm following the helpful "nRF Connect for VS Code" video series on YouTube to install it on my Windows 10 PC. Everything was going...
