Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hello,
I am using nRF52832 chip for freeRTOS project and using RTC2. I have SDK15.2. I want to have timestamp from RTC as hex format. I searched almost all forums but i...
I am trying to setup unit tests for my app using the instructions from here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_unity_testing.html
To get...
Hi,
We are using AT%XVBAT command to get battery voltage and detect low battery.
We facing issue in CFUN=20 mode, sometimes AT%XVBAT is returning latest voltage and sometimes...
Hi there,
I would like to add some extra data to mesh-nodes, when not provisioned -- with ble_advdata_manuf_data_t usage. What is the best way to do it and where?
And...
I have a simple OnOff client server running on Zephyr. I'm developing on macOS and platformio.The nodes are self configured. If I restart the client it cannot reconnect to...
Hi,
I want to add LIBUARTE example in nrf5 sdk into mesh light switch server example, I would like to know how to do that?
I'm using nRF5_SDK_16.0.0 & nrf5_SDK_for_Mesh_v4...
Hi All,
I am trying to implement I2C Slave functionality on NRF52832, So NRF52832 will act as a I2C slave.
So i found there is an example TWIS Slave and TWI Master Mode...
Hello,
I'm using nRF52840. I developed a project using openthread libraries: in particular I included " libopenthread-nrf52840-softdevice-sdk.a " library to have the CLI...
Hello. I'm using the NUS BLE service to send ADC sensor data. I am having the SAADC callback function call ble_nus_data_send() to send raw samples. I have set the min and...
I need to measure full power consumption of nrf52, on PCA10040 from... a 5V source (because including some other 5V devices). I measure it from 5V pin and not usb plug. I...
Hi,
as I know from the mesh spec, the number of elements cannot change after a device was provisioned. Nordic even went so far as to define the number of elements during...
Hi, how to measure RSSI in OpenThread? I have 2 nodes, what is correct state that I have to assign to each node to do transmit/receive test, is it leader and router? or router...
Hello,
We're thinking of powering external sensors through GPIO pins configured as high-drive. The sensors themselves consume only a few milliamps at most, which is easily...
Hi,
I would like to control a piezo driver using GPIO pin on nRF52840 DK.
I've read posts about this kind of application. But still confused about how to set up PWM...
