SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Here I am working on NRF52832 + SDK15。
I have designed two board with different 52832 package ( N52832-CIAAB0 and N52832-QFAAB0 ), I have disabled all peripheral part and...
I am using nRF51822QFAA & S120(v2.1) & SDK10.0.0
The application is to scan nearby ibeacon and send the ID information by UART. But the application always hang / reset...
When the nRF52 micro-controller is programmed through batch file i.e. nrfjprog utility, the flash fds fails to initialize.
Every time, flash fds initialization fails, I have...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
I want to turn on the LED in Thingy:52 in a particular color if a particular condition is satisfied. How can I address the LED and turn the LED on in the desired color in...
Hi,
I am using the UART exmaple as a skeleton code to get RSSI from a peripheral nRF52 DK. I am working with the SDK V14 and I want to integrate my code with an arduino...
Hello, Nordic engineers. Thank you so much for spending your time solving my problem.
Currently, a custom board is made with the Nordic nRF52832 chip. As I have studied...
Refer to this post ， I did the same job to change simple_on_off model into generic OnOff Model , and I could control the LED state with nRF Mesh application as well.
I have...
Hi sir,
we used nRF 52832 ESB protocol ，
use
NRF_ESB_PROTOCOL_ESB_DPL
#define NRF_ESB_MAX_PAYLOAD_LENGTH 128
bitrate = NRF_ESB_BITRATE_2MBPS
so how can I config...
My app (S130 SDK12.3; BLE with multiprotocol support where the radio session is opened before advertising) registers function sys_evt_dispatch() as per
but sys_evt_dispatch...
Hi,
I am not yet familiar with NFC and have a question about using NFC with the nRF52.
If I understood it correctly the nRF52 is a "listening device" i.e. it cannot...
Hi Nordic,
I am trying to do a time critical data acquisition in a BLE based application.
Earlier I was using software timers. But, since the software timers are not accurate...
Hi all, I have some question for ask :
I add NUS service into light switch proxy server example. And I only run nus service part (Don't run Mesh part)
when I use IOS to...
Hello All, Please help me. I have nrf52840 and added json parser which is large and nested. Json_parse fails , is there anyway to enlarge heap size?
Any feedback must be...
Hello,
I'm trying to flash wt51822-s4at using nrf52dk ( https://4tronix.co.uk/picobot2/WT51822-S4AT.pdf)
It has nrf51822 chip on board
The firmware goes through without...
