Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am using a power profiler to measure the timing of my program and I found something wrong. So I tested with a simple pure timer.
So first I set the timer during to 300ms...
I just spent 2 hours chasing BLE bug after upgrading from s132 v3 => v4.0.2
I added a call
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg)...
I couldn't use nRF Connect (BLE) under Linux, after updating the FW, it tries to open /dev/ttyACM0 but fails to do so.
Not a "permission" problem: the user is in uucp...
Hi,
I'm unable to compile the OpenMesh example application. I've modified the make file with correct paths. However I'm getting the following error. Can you please help...
I have a NRF51 talking through the UART to another uC, and I'm trying to log messages through Segger RTT. Everything works normally until I start to send some data through...
If SEGGER_RTT_CONFIG_DEFAULT_MODE is "BLOCK", the program won't start without RTT attached - at least for me... is there a possible solution?
I mean, technically it makes...
hello ,everyone
I was confused by a PWM problem for a long time , on nrf52832 SDK13 ,i wanna change the PWM duty cycle every period ,but now i find can not change it at...
Hey dear Devzone,
I am trying out some Thread and BLE dynamical examples on my nRF52840's but running into some problems using the " ble_thread_dyn_mtd_coap_cli " example...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
Hi there,
hope you are doing fine.
I am using SDK 14.1 with SoftDevice 132 as well as a state machine framework which needs a have a function called periodically to...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
When I want to disconnect central, I'm using sd_ble_gap_disconnect function as below.
err_code = sd_ble_gap_disconnect...
When I try to build and run any example from the nRF5 SDK, it can compile successfully. But when loading to the eval kit, it can't find the 's140_nrf52840_5.0.0-2_alpha_softdevice...
Hello Everyone,
I am using nrf51822 256Kb Flash and 32KB RAM Raytac's BLE module with SDK11, S130 with over the air Bootloader (16Kb).
So the aim is that when a particular...
