Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
I use nRF6310 and PCA10005 to develop BLE project. When entering DTM tab, I cannot find the motherboard on "set up on".
DTM.jpg
My hardware is:
motherboard: nRF6310...
Dear Support,
we have done some technical question
About the N5 module of Dynastream (with nRF51422) we would like to program the software placed into the application...
my android program add many nRF51822 devices mac adress to a file in my android device.So I can count number of connected nRF51822 to my android device with bluetooth low...
Hi,all.i want to integrate ble_dtm(6310 board) to ble_proximity(pca1001 board).Can someone give me advise? i run ble_dtm on my board,and cannot find "Nordic_DTM" when i scan...
Hi,all.i want to construct our product test system.i follow AN34 page6 (figure 2) to do this.i have a question: DUT and nRF DK module run same firmware ? if correct,when nRF...
Hi,
In my application, I would like to take some action, when the bonding is removed from the phone.
At the moment I'm using static key for bonding and I see that BLE_GAP_EVT_SEC_PARAMS_REQUEST...
I'm using SDK 7.1, SD310 2.0.1, MCP 3.8.0.7
I have two versions of a board with the nRF51. Some of them have the 32kHz crystal and some don't. In my application I have...
Hello,
I am working on an application based on the "Motor control example". However instead of just setting two different values for the duty cycle I am trying to either...
Hello,
I have started to study your UART to/from BLE sample but after reading the following post ...
devzone.nordicsemi.com/.../
... I have a big doubts.
Due to...
Dear Nordic,
I am using a pretty much unmodified version of the BLE HID Keyboard example from the Nordic BLE SDK (straight of github).
I only modified pins, and disabled...
In Short: How to get status wether noticiations are enabled or not? Where is this stored?
Hello,
I would like my peripheral to start/stop a timer that does measurements...
I have a project which will send the temperature from the nRF51DK to host.
The value of the temperature is an integer. As example Value:0x00000A2B -> 2603 ->26.03°C
...
NRF24L01 has its own protocol, but I do not understand the protocol itself is how to handle the payload sent and appear in the header contains the same Bite, whether to adopt...
