I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
IDE: SEGGER Embedded Studio for ARM 5.32 SDK: nRF5 SDK 15.0.0 and nRF5 SDK for Mesh 2.1.1 demo: examples\sdk_coexist\ble_app_uart_coexist\pca10040\s132\ses\client_pca10040_s132...
I am using NRF52 DK board and removed SB9 track to connect my ammeter for current measurement . I have taken ble_app_blinky ( peripheral example ) from SDK15.3.0 .
My application...
hi,all
I'm using nRF52833, s140.. pca10100.
I want to read my pcb's touch gpio..
If I touch it, it falls down to low. ( I checked it with scope..)
When viewed through...
I'm testing USB audio demo. I changed bit resolution of APP_USBD_AUDIO_FORMAT_DESCRIPTOR 16 to 24 but the widows10's USB audio device is still 16 bit. how can i do that?
Hi!
I'm trying to pass the BLE data to the PC using nrf52840 DK.
To do so, I've started with the ble_app_uart example and it was able to build fundamental features–find...
Hello,
our application requires to emulate keyboard, e.g. to write strings like "hello world\n" as it might be typed by the keyboard. According to the recommendations...
Hey I am using nRF 52840 DK
I am reading temperature from Segger code and displaying it in the log
But I want to display that value in my android nRF Mesh Application...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
I created a 500ms timer to send mouse movement as follows.
m_mouse_movement_send(5,0);
When the device runs there, the device will restart. The error code is NRF_ERROR_FORBIDDEN...
Hi engineers,
I want to use the pin P1.09(NRF_GPIO_PIN_MAP(1, 9)) as GPIO, but when I initiate it, it seems fail.
I've looked through the relevant issues here, but got...
Hi,
I am currently trying to build a project using a nRD9160 with legacy code and am receiving this error when trying to load an existing project:
I understand...
I am not able to successfully use your nRF UART app to communicate with your nRF52840 DK. I get a warning when installing the app that it may be too old for my version of...
I'm still learning BLE development so I apologize if this is a basic question.
Here is a screenshot of a recent capture I did with the nRF52-DK. The bluetooth sniffer is...
Pardon my ignorance of the nuances of Security and Encryption but what I am observing is a bit perplexing.
Every time I run the nrfutil command to generate the bootloader...
Hello, I use sleep_mode_enter() to put the device into sleep mode, however, the RTT print a fatal error after sd_power_system_off(), I don't know whether the device is in...
