Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello.
I just import Thingy firmware: thingy52_ses.zip and try to build this project and check possibility of programming my Thingy, but SEGGER returns something like that...
When I use nRF52840 dongle as a promiscuous packet sniffer , I found that sniffer works fine no matter how much I set the baud rate. This happens only on the dongle, so I...
Hello,
I have a PWM code that works as a peripheral application on my nRF52 DK, but now I want to set it to be controlled via android phone app. I have nrf connect on my...
Hello,
I'm a newbie to BLE and the Keil uvision IDE. I'm using a nrf51422_xxac_s110 chip, The version of the IDE I'm using is 5.28.0.0. When I add the fds.c file, into the...
Security of data passing in BLE communication Hello I am developing based on "multirole lesc" of BLE sample project. What is worrisome about the project is the "security_req_t...
I don't program the BLE part myself but I must know from a design-level.
As I understand, a BLE scanning unit must connect within less then 60us after advertisement.
If...
Hello.
In according to this tutoraial: https://www.novelbits.io/bluetooth-mesh-tutorial-part-5/
I wonder if it is possible to replace ,one of these two nrf52840 DKs...
Hi,
Has anyone had success going from the Arduino bootloader back to J - link bootloader?
CONTEXT: I purchased 5 nrf52832 modules, and followed the posted guide to burn...
Hi, I would like to power my development board from the provided coin cell. I removed the plastic between battery and negative contact point. I put VDD position on power source...
Hello. Can you tell me which project can I use as a template from nrf 5 SDK with basic RX/TX data send/receive payloads API? Want to build custom simple-structure mesh, with...
I want to use some functionalities of Zephry OS. Example https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.0.0/zephyr/samples/gui/lvgl/README.html .
I also want to...
I am rebuilding my computer after experiencing a corrupt boot sector and am reinstalling all my apps. I am moving from Kiel 4 to Kiel 5. My project loads, but it says that...
Our manufacturing supplier provided me a log file from the nrf Connect for Desktop Application that shows repeatedly unexpected disconnects when nrf Connect opens a second...
Hi,
Do you have a sample ANT radar profile example with all the pages defined, similar to ant_hrm.h in SDK 15.3 components/ant/ant_profiles/ant_hrm/pages/?
Thanks,
Abid...
Hi Admin,
I just bought development board Thingy 52 from Digikey. I coudn't find design files that consist of hardware design in Nordic website. Could you advise for this...
