Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Is it expected to get an EINPROGRESS error when calling nrf_connect() with NRF_O_NONBLOCK set. How do I know if the call was successful or not? Should I expect a positive...
Tested with PCA10040 1.2.4 bare board Chosen p0.11 as it seems to connect nothing (floating)
I would expect the code below always prints "<info> Main: [11] 1 1 1 1 1", no...
I'm working on a custom DFU bootloader using the Secure Bootloader example in the nRF5 15.2 SDK. My board only has one LED and, during DFU, I'd like to using blinking duty...
I am using SPI 2 (not SPIM) and just migrated my project to SDK14 from 13.1.
I kept getting "Wrong configuration" on compile, until I realized that on the nrf_srv_spi.c...
Hi!
nrf52832, SDK15.0, central side. S132.
I connect my nrf52 in HID mode to android smartphon Samsung А8+ Android 9.
In a log I see connect- disconnect with error code...
Hi,
When using CFUN=0, the modem stores settings (such as system mode and successful network connection information) to the flash from what I can gather, but it then needs...
At certain times, I would like to disable the SoftDevice's control of the PA/LNA control lines and return them to normal GPIO lines.
When the SoftDevice is using the provided...
I am using nrf52832 module with SDK 11.0.0, s132. I am advertising and the central device is able to scan the advertising devices and displaying the RSSI and peer address...
Hello again Nordic World.
We are slowly attempting to transition from the nRF51 environment to nRF52. We are starting, not with development environment for our product,...
IN-119
it says t he affected versions are:" All versions of S110, S120 and S130 S132 v2.0.0"
does it means all versions of S130, or only S130 v2.0.0 affected?
When using ` nrfutil settings generate` to generate bootloader settings and merging with soft device and App, how do you then use `nrfutil pkg generate` to generate a package...
Hello, I am working on the modified versions of hrs and hrs_c examples, on two NRF52832 with s132. I modified the apps so that when they connect the peripheral reads from...
Hello,
I have a fewURGENT questions.
I have the NINA B112 by u-blox on a custom PCB (datasheet here ). We require regulatory testing of the BLE. The NINA B112 is based...
Hello,
I used to send it successfully on nRF52810.
Two chips, one as the master and one as the slave.
Using SDK15.2.0
Now, I want to port to nRF52811
Related header...
