Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
I am generating a pwm signal in pin no:21 of nordic nrf51422 board. i connect this pin to pin no:24 using a wire in the same board and want to count only rising pulse edges...
How to decode opus file on Android or how to configure NVS on Android?
we have a Android TV device to connect Smart Remote 3 of nRF52，but audio from the Smart Remote is codec...
I am just trying to program my sample nRF52810 using a PCA10040 devkit.
I get the message "No device detected, or readback protection may be set"
Pressing the Recover button...
Hi,
I'm working on an application with an accelerometer without SoftDevice (for the moment).
The accelerometer communicate in I2C. It send an interruption when a new sample...
hi
I develop nrf52832 based ble device, this based rtos therefore ble communication have critical
time limit.
I will use mesh protocol my ble device, in the environment...
GLS is implemented using Nordic(S110_7.0_SDK6.1).
When set to Control solution function.
The setting of the device and the READ value of the application do not match...
I am trying to integrate an iBeacon Library on nRF51-xxAC with SDK10.0.0 and S110v8.0.0 . Can anyone please help me out if any one has ported the iBeacon Library and what...
I want to implement one central device to ten peripheral devices connections.
I'm using nRF52832 DK and S132 5.0 and SDK 14.0.
So, I have run multilink_central example...
I managed to sniff Nordic mesh sdk 0.9.2 packets on raspberry pi 3 using "hcidump --raw", and I can read the raw hex data of mesh packets of light control demo, but since...
Trying to interface this module with atmel core micro.
We are able to transmit data by this module but not receiving the data at other end.
At transmitting side we are getting...
Hi,
Currently I'm working on nRF52 with SDK11 and SoftDevice S132.
Till now I've worked with IAR and my code was based on the "ble_app_uart" and the dfu "bootloader" examples...
WHAT EXACTLY IS THE PURPOSE OF PPI. IF I AM GENERATING A PWM SIGNAL IN PIN NO 21 AND USING A WIRE I CONNECTED TO PIN NO :24(BOTH GPIOS) IN NRF51422 BOARD AND WANT TO COUNT...
Hey I was using the relay example in SDK 12.2 on the s132 NRF52DK.
We added a service and characteristic using the Nordic tutorial - devzone.nordicsemi.com/.../
Using...
I have a very simple test script which enables a BLE service (only the Generic Access and Attribute), advertises and waits for connection. It also sets four pins to input...
We made a READ request from the client with nRF 52 as BLE peripheral.
READ was automatically repeated 10 times when writing 200 bytes of data in a characteristic fashion...
