Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello,
I am using Nordic nRF52840 (nRF5SDK v16.0.0) and softdevice : s140.
Nordic MCU is connected to Host MCU over UART interface (baudrate = 115200). I have below observation...
hello,
i am using nrf52840 with sx1276 i am trying to change some of the calls from arduino to nrf52840 can you tell me i am doing everything right
#define DIO0 NRF_GPIO_PIN_MAP...
Hi. I use NCS SDK 1.5.1 with NRF5340 .
I took the project from: \zephyr\samples\portability\cmsis_rtos_v2\philosophers\ as base and try to add two additional tasks.
Application...
Hi,
I would like to implement cell triangulation with the nRF91 in order determine the location of the device via cellular. I already had a look at the available posts such...
Hi friends:
My ble mesh gateway want to remove a mesh node
(a): Which api can i use to realize this purpose?(My SDK is nrf5_SDK_for_Mesh_v5.0.0)
(b): There is a special...
Hi Community! We're happy users of a range of Nordic solutions on behalf of our clients in Europe. Now we're facing a new challenge: one BLE device that should act as a sort...
hello,
i am using nrf52840 with sx1276 module i am using an library which consists of c and c++ files i want to complie both the file but when i complied the following c...
Hello!
I think I have the below problem, except I am using NRF52840 and therefore PCA10056. I am using SDK14.2 and the alpha softdevice. I am aware these are out of date...
Hello everyone, I would like to ask about the examples of openAMP in nrf5340. I only saw examples of network core in nrf\samples\nrf5340\multiprotocol_rpmsg. Where should...
Hi. I am a beginner with nrf52840. Trying to get SPI and an I2C peripheral working at the same time using the SEGGER Embedded Studio. I have working version of both the I2C...
Hello,
I am using the nrf9160 to develop a cellular product but am seeing inconsistent end-to-end connectivity results. For the nrf9160-dk and a custom board based on the...
Some transciver can improve RF performance like output power and EMV, through supply higher DC voltage. Did nRF52840 have the same characteristic with BLE? Is that high votage...
Hello,
I have a questions on the ADC and GPIOs front end input resistance over operational temperature range, as our final product operating temperature shall well beyond...
Hi,
we are developing a custom board based on nrf9160 that include CAN bus. When updating nRF Connect SDK from v1.4.2 to v1.5.0 we can not get CAN-bus up and running again...
Hello,
For our device we are using a NRF52832 and SDK version 17.0.2. It only has one Button connected to P02. Due to needing the device to be water resistant the decision...
