Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I have several asynchronous Đ°periodic sensors with their interrupt handlers. My service should gather the data from those sensors and do some math. The outcome of this math...
Dear all,
I tried to program and test the iBeacon application on the s110 folder from nordic examples.
The code on the Cortex-M0 has problem. Seems during programming...
After program nrf51822,it works normaly.But when I program again,it can't debug.NO SWD and NO USB DEVICE.So I can't use nrfGoStudio or nrfjprog.exe to recover it.When I pull...
Hi,
I've set up a streaming solution that is easily streaming 4+kBytes/s to an iPhone. I've also set up an ADC service that is sampling at 2,083 Hz 10 bit mode, using a...
Hi,
I am using nrf51822 (128k).
Softdevice 6.0 (s110), SDK 5.2.
How can I send an empty notification packet (data length 0) to master device?
If I send a packet with data...
I was wondering whether it is safe to use a delay (such as implemented by nrf_delay_us) to, for example, delay an iteration of a while loop, or that it is always better to...
Dear Sir/Madam,
I am testing iBeacon application on the nRF51822 mounted on nRF6310 motherboard.
I programmed the ble_app_beacon application in the keil_v5\ARM\Device...
Hello,
I get a sample code in the dir flllowed after intsalling nRF51 SDK:
\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon_code\main.c
but I still...
I ve installed CSR bluetooth 4.0 adapter , it can communicated with even the bluetooth 2.0 devices, how ever it even can not discovery the board when I programed the softDevice...
Hi,
I have ordered nrf51822 development kit with one of my local vendor. when the product came to india , it was checked in customs office somehow the samples in the kit...
I'm using an nRF51822. Currently, I'm using the low power sleep mode. The device uses about 1.5 uA in sleep, which is great. The firmware wakes up the device every n minutes...
I have a fully functional code for 8-bit data acquisition using nrf24le1. Now i want to upgrade it to 12-bit resolution ,but i have problems in doing so .
In my project...
I am making a module using nrf51822 and a chip antenna.
I need a layout from nrf51822 to a chip antenna through matching chircuit.
Unfortunately, I don't know how to...
Hi,
1. I want to design a product as a tag,which can read the temperature and transmit the data to a host,the host can read several devices' data. which mode would I use...
Hi everyone,
Just recently I've got two nRF6310 EVB boards with a nRF51822!
When I connect board via USB and open the nRFgo Studio, it can recognize the board as nRF ISP...
