I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I'm running into a bit of an annoying situation every time i run ' west flash --build-dir ./build' in the command line. It rebuilds always after a successful build i set when...
Dear Nordic team,
I have a complex question. In my project I use components which operate at 2.25V as well as they expect 2.25V logic levels.
My idea is to use nrf52840...
Hello I am trying to implement AES Key Wrap on nrf54l15. For that i enabled ``` #necessary to get oberon_psa_wrap_key/oberon_psa_unwrap_key CONFIG_PSA_WANT_ALG_AES_KW=y #necessary...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Description:
I am experiencing a non-linear "sticking" and "jumping" behavior when attempting to monitor the VDDH rail using the internal VDDHDIV5 channel on the nRF52840...
I don't know where to make this suggestion, so hopefully my suggestion makes it to the right person.
I completed BLE Fundamentals and the nRF SDK courses.
I would have...
Hi! I'm migrating some code from an 14.2.0 SDK to the 17.1.0 SDK and cleaning up a big mess.
Whenever I call nrf_power_pofcon_set ( true , NRF_POWER_POFTHR_V27) with either...
I am trying to debug/flash an nRF54L15 using the nRF Connect VS code extension and a J-Link EDU. Although my J-Link EDU works fine with all the Segger tools, including Ozone...
Hi
I am looking to a wearable / health tracker which will be mounted on a persons head.
Are there any precertfied nRF7002 module where I don't need to go through the pain...
We tested several hundred connection and disconnection cycles with the nRF52840 BLE dongle. The first hundred cycles operated without any issues. However, at a later cycle...
Hello, I am trying to use twister + ztest to run some basic tests on my device custom project and nrf5340 Here are the contents. Current Directory Structure
Contents of...
Hello there,
I'm developing a project with NTN using a Vivo chip, a Brazil operator chip, but I'm having trouble with an nRF9151 and I'm trying to put it in NTN mode, but...
Hi
I took over a nordic project and was asked about the bluetooth version used in that project.
How Do I figure this out?
I am using a nrf52833. The firmware is developed...
Hi all
While connecting to a peripheral that has ble buttonless dfu characteristic i need to enable indicate.
Undortunately i get back err: 0x11(17) from sd_ble_gat...
I'm struggling with the nrf sdk v2.9.2 zigbee light_switch example. I copy the example, add this to proj.conf
CONFIG_ZIGBEE_CHANNEL=25 CONFIG_ZIGBEE_CHANNEL_SELECTION_MODE_SINGLE...
