before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hello
I am using a Nrf52832 kit from Murata japan distributor.( https://wireless.murata.com/mbn52832.html)
My purpose is to be able to perform DTM on above mentioned kit...
Hello,
I am working with Window Covering cluster.
I receive command ZB_ZCL_WINDOW_COVERING_GO_TO_TILT_PERCENTAGE_CB_ID from my coordinator successfully, but I can...
Hello
I need to broadcast large amount of data on MQTT ~ 300K
I require to send it as fast as possible
how can I best calibrate settings for maximal speed send via...
i am using ble_app_uart example on nRF52833 board. I want to make a function that whenever I press button 1 on board, the board will disconnect Bluetooth connection with my...
Hello,
We are developing a BLE beacon with nRF52810 and SDK17.0.0. I modified the code on the basis of ble_app_beacon. I rewrited m_advertising.adv_modes_config.ble_adv_fast_interval...
Dear friends:
The ble advertiser device can advertising, the advertising can be monitored by a smartphone.
The ble mesh node with proxy feature also can advertising, the...
I encountered an issue where my firmware would get stuck in NRF_LOG_FLUSH();, and the same logs would be sent over RTT repeatedly. Pausing the debugger showed that the read...
Hi
My purpose:
Send 180 Bytes per 10 millisecond
I got a problem:
I use NUS project in NCS SDK15.0,when I send data per 10 ms,It return"Failed to send data over BLE...
To the kind attention of Nordic support team,
We would like our BLE nRF52 based product to reconnect as fast as possible.
My question is: are there side effects in having...
Hi,all
I want to connect my NRF52832 device with pc, then , use the value uploaded from the device to draw a curve in pc. Refer to nordic engineer's advice, i used the heart_rate_collector...
I want nRF9160 to do mqtts connection without certificate.
Modem FW:1.2.3
Here is my mqtt client_init:
When I use 9160DK, mqtts is connected normally. But when using...
Hi Everyone, I am confused in sleep modes of nrf52832. Can you please tell me the difference between System ON sleep mode and System OFF sleep mode?
also the current consumption...
Dear friend，
Based on SDK15.3, using S332 protocol stack, running on nRF52832-QFAA. Connect the device with a mobile phone via Bluetooth. The connection parameter Min connecion...
