Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I have already went through every step as per what the documentation has stated, but I could not be able to sniff any ZigBee packets using Wireshark. I only want to perform...
I am trying to develop a first eval / test program for the BMD-340-EVAL evaluation board using Keil. However, I don't seem to be able to download the required Keil pack. Other...
Hi,
I want to send multiple packets on a notify characteristic using ble_blanky app as baseline but only first 4 consecutive notifications are received on android side....
I would like to set the UUID below, so please tell me how to set it. 1)base UUID: 2)Service UUID： 3)Status Characteristics UUID： 4)Control Characteristics UUID： 5)Blood...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I set tx power in advertising as below.
sd_ble_gap_tx_power_set...
Hi,
We are developing a product that consists of a "central" and "peripheral" device. A small amount of data is periodically send from the central to peripheral device...
Hi. We are using nRF52832 and we have problem with UARTE. SoftDevice version - S132 5.0.0, SDK version - 14.2.0. Our application uses nRF and Mbed Serial to communicate with...
I have created my own custom project based on the template ble app, porting over the relevant includes and settings in order to start fresh. Despite my section placement file...
Hello,
I'm using a development board PCA10040 with sdk 16.0 I'm trying to organize a data streaming between two devices. Nrf52 board collect data (27 bytes with interval...
I bought dev board for evaluation purpose (currently run on ESP32)
chip: nrf52832 board: E104-BT5032A-TB ( http://www.ebyte.com/en/product-view-news.aspx?id=956) framework...
Hello Nordic! Im making a custom Nrf5232 QFAA, and for the antenna, I want to use only a grounded micro-coax connector and not a trace antenna, is this even possible? I've...
1. I want to use the following command line to compile the nrf9160 project, but the error.
2. Can you help me find the cause of this error?
3. Please provide me with...
Hello, I encounter a problem when I am trying to measure the current consumption of the nRF52840 on the nRF52840-DK. I have set the board in direct supply mode as described...
Hi,
I'm using a nrf52832 based beacon with some sensors attached. To retrive the current time I use the CTS client. Actually, I'm following the ble_app_cts_c example to...
