If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am receiving repeated POLLHUP and reboot on my nrf91DK board (see attached log).
1) I have loaded the modem firmware with mfw_nrf9160_1.1.1.zip. (I also tried version...
Hello Nordic,
I have a sparkfun nRF52840 mini and I want to know which project from nRF5_SDK_15.3.0_59ac345 should I use to have my nRF52840 slave in the TWI communcation...
I am currently working from an SDK16.0 peripheral example utilising freeRTOS and polling the softdevice (NRF_SDH_DISPATCH_MODEL == 2).
This has worked fine for nRF5 SDK...
I have some problems with the TWI (I2C) and it seems that TWI1 does not send anything. I have managed to create a simple example to recreate the issue. I am using TWI1 instead...
Hello.
Is it possible to send more than 1B data via blinky characteristic from central to peripheral? I made my project with two characteristic (my own 128-bit UUID) basing...
I am using android ble with kotlin. I ported the Blinky example to kotlin. There is a reference escaped in object construction when on construction the BLEManager invokes...
Dear Nordic Team!
I am verifying my tools chain for nrf52840 Mesh project development by mesh light-switch example. I have 4 PCA10056 and make them to 1 provisioner, 1 client...
Hi,
I use sdk16 and nRF52832.I want to change advertising in the air:
Now I'm using the timer to change the adv.But I want to change adv with RF interrupt.
Like this...
I developed an application (BLE named Adriano) using nRF52840 DK, nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730, starting from ble_zigbee_dynamic example. I added some custom...
Hi,
I'm developping an application for nRF52840 as a BLE central. It is supposed to connect to an Android device (BLE peripheral) using a bond (encrypted connection with...
Hi everyone,
I went through the source code by Vidar Berg for background dfu using SDK 15.3. I am working with nRF52832 , S132 and SDk 12 with Keil IDE. I did try with secure...
Hi,
I am currently developing with nRF52811 chip using nRF52840 DK. Where can I find a reference 2.4GHz PCB antenna design document?
Thanks.
Regards,
Jxq
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
hi, i am facing this unknown error at "unknown function at 0x000008C8",
i am doing a development project with nrf52832(sdk14.2 and s132v5,ble nus is used) mcu and sim800...
Hello, I'm developing SAADC on nRF52832.
While developing, I have problems now.
I applied sine wave on ADC input.
And the result is displayed on the figure that I...
