Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
v0.12.0 provides sd_api_v 5 support that I need but its not released in pip. v0.12.0 is available (in pypi) for windows but not for Mac/linux.
Please provide also linux...
Hello!
I'm trying to make the asset_tracker sample working on the nRF9160 DK. The at_client worked just fine and I was able to connect to the base station (I'm using NBiOT...
Hello, We have been using the PCA100059 version 1.0.0 dongle with a custom firmware which fails to run on the new PCA10059 version 1.2.0. Unfortunately there doesn't seem...
Hello,
Im a beginner in microcontrollers programming, just started with the pca10056 and pca10059. Im aiming to develop a beacon scanner for pca10059, to send data via usb...
I compiled and debugged the PCA10040e ANCS example (ie emulating the 52810 using the 52832) from SDK 15.3 - successfully. But I wanted to turn off code optimization to facilitate...
Hello,
As many mobiles do not have NFC I would like to use LESC OOB pairing with an QR-Code which could be shown on the device terminal. Well, I know where the NDEF message...
SDK version :15.2
question； when i use app_timer , i got interrupt which is not i wanted.
i creat and start timer :
app_timer_create(& m_timer ,APP_TIMER_MODE_REPEATED...
I'm using nRF SDK V15 with nrf52DK board, running the ble_app_hids_ms example.
I I want to have continuous non-stop advertising duration, should I have both APP_ADV_FAST_DURATION...
Dear Sir/Madam,
My question regards the behavior of the EasyDMA during the transfer of data to / from a serial peripheral like SPI or UART.
Let's suppose that during the...
Hi all,
I using SDK 15.1 and 15.3 for test.
I am working with DFU for NRF52810.
I tried success for NRF52840.
But I can't update success for NRF52810.
Below is scrip...
I use the Firmware «AT host sample» on Thingy91. Then I connect to Swisscom network on band 20. The current consumption is about 3.5mA. Then I send AT+CFUN=0 or AT+CFUN=4...
Hi All
We are using nRF9160 DK, and we are working on ADC channel. we use This example of ADC. I am using single-ended with no over-sampling with a gain of 1/6, reference...
Hello
my setup is sdk 15.3, nrf52840, s140, open bootloader and an application.
Everything is merged, flashed and running and no changes are made at the standard addresses...
