Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
As a master device with a whitelist there is a limitation on how many slave devices can be connected. If i am correct, other than whitelist there is no restriction to the...
Hi,
How do I receive data from host (computer) on my BLE device(Nordic board)? I want to use a simple open source HID API to send data to Nordic board and glow an led or...
Hello, we have finished all prototyping with BLE modile from Taiyu Tuden, this module: https://www.yuden.co.jp/wireless_module/document/datareport2/en/TY_BLE_EYSGJNZ_DataReport_V1_9_20180530E...
Good day, I am new to this forum so I am having some problems posting my question. Sorry for any inconveniences. I am having serious problems flashing my custom NRF5282 board...
I want to connect nRF52832 with PC. The objective is using nRF52832(I am using BT832 Module) I have to scan all Blue Tooth deceives details and send to PC. Please help with...
Hi,
I am using a custom board with the nrf52832 with SDK 13 and I have a bootloader and an application that both configure and feed the WDT.
However, upon restart (power...
Is there any straight forward way to detect jamming using any technique on this Nordic device? I'm using SDK 15.2, Soft-Device 6.1 Would this be possible by the new SD 6 function...
I have been using SMD modules with NRF24L01+ fitted.
The first batch I used worked fine for months.
Then I purchased another batch and found the tx_ds_active or max_rt_active...
Hi,
1. I went through the document. I'm trying the example applications Light-Switch on PCA10040 DK and NRF5 SDK for Mesh V2.2.0. So it is like the Client will be provisioned...
Good afternoon,
Following up my previous case, to which I got no reply, how can I use a queued write characteristic to write less than 20 bytes of data?
I'm using it...
I'm trying out Zephyr on the nRF52 DK, specifically I want to test the ADC drivers. Since things are moving quite fast in the Zephyr development world, there may be some information...
Hello, I'm working on Mesh SDK 2.1.1 and I'm trying to send a Relay Set message through Configuration Client. I have changed the code of models_init_cb() function inside the...
The nrfx_spim driver has an issue when chip select pin of the driver is not used.
When nrfx_spim_init is called with a nrfx_spim_config_t whose ss_pin is set to NRFX_SPIM_PIN_NOT_USED...
Dear Nordic
I have custom board(nRF52840) its not detecting through Jlink (from nRF52 DK).
I tried to connect nRF52840 dongle(using J2 in dongle) with same setup its detected...
