Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I'm getting Error 7 too few arguments to function 'lib_aci_set_local_data' C:\Users\nishant\Documents\Atmel Studio\6.2\ATmega_AdafruitLIB_nRF8001\ATmega_adafruitLIB_nRF8001...
Hello,
as far as I found out, a Peripheral that advertises will stop advertising as soon as it receives an incoming connection (BLE_GAP_EVT_CONNECTED). A central will however...
I'm using the nrf51822 with the IoT softdevice and SDK as an IPv6/6LoWPAN peripheral and Linux with a BLE dongle in the central role. Basically, I have everything working...
I'm trying to write 7 bytes (0x01 02 03 04 05 06 07) to my nrf51 Dongle with my own custom service running based on the Battery Service.
The problem is that I can only...
Why does it say that the nRF51822 has 1Mb/s and 2Mb/s data rates if it doesn't?
Quote from devzone: "6 * 20 B* 1/0.0075 s = 16 kB/s = 128 kbps".
And its only for S110...
Hi there
I am having problems with uart app on SDK V7.2
I have dowloaded Keil and all of the other demo's seem to be working but this one is not.
It will not connect...
Hi. i have a little problem.
For start, i want to use the referance Layout found here link text with the hardware description file of PCA10004.
So there is a simple method...
Previously, I used to load and debug my programs.
after a few months,
Today when I setup the environment again, now I can only compile and generate hex files from Keil....
Hi,
Now I am try to use sd_flash_page_erase() to erase a flash page.
Before I call it, I already stop all interrupt but I always get a error message "NRF_ERROR_NO_MEM...
Hello,
I am working with nRF51822 development kit (s130 softdevice). I want to use one software interrupt for my custom application. Is there any software interrupt available...
During my development with ANT protocol, I found that if you have a bunch of units all have one master channel. Channels will actually bump into other channels easily and...
Hi,
I'm trying to get the SPI Slave example working on my nRF51822 PCA100001 development kit.
SPI1_TWI1_IRQHandler never gets called even though the ACQUIRED and...
Looking into the schematics, I could not find any uart or spi signals on the connectors. I am good in soldering, but I would not dare connecting wires to the nrf51422... ...
