Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Dear Nordic. I am working in the device that require the controller to measure its VDD line to ensure that the the device goes into sleeping mode (very low current and do...
Is there any code example for Android or iOS on how to build / send a DFU request for NRF_DFU_OP_FIRMWARE_VERSION and then how to interpret the response that comes back? ...
I want to receive data through UDP in eDRX
I tried to set up non-blocking UDP by reading this post, but I can't achieve the function yet. Any help? https://devzone.nordicsemi...
Hi all,
I am successfully using Openthread for an application on the nrf52840. As the application is growing I'm thinking about utilizing a RTOS. Therefore, I am currently...
Hello. I have integrated signature validation before boot in my boot loader. This uses the `nrf_dfu_validation_boot_validate` function, which eventually calls into `nrf_crypto_backend_secp256r1_verify...
I use the above code to copy the device root key from the flash region. The if condition at the end results to FALSE always whcih implies that the key was not copied into...
Hi,
I would like to confirm whether bootloader should start from my application with BLE buttonless DFU. Once the request to enter the bootloader is received by my app I...
Hi,
I am running the Asset Tracker application from a fresh clone of the 0.4.0 nRF connect SDK. Using the supplied iBasis SIM.
It connects after booting, and I can monitor...
Hi,
Iam using nRF52840 , And got ANT sdk from thisisant.com. Placed in the required folder & Using ANTware II v4.1. All things going well, But after programming the DK nRF52840...
Hey Nordic Community ,
I have been trying to get the Modem firmware up and running without success for a few days now (Attempted with 2 different PCs and 2 DK with same...
hi....
i am using nrf52382 .. segger 15.2version
here i have attached two programs ble_uart and twi sensor ... its working fine but data is received over ble_uart app...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use CURVE25519.
I made my code refering to example "ble_app_multirole_lesc" and "nrf_crypto_keys.h".
NRF_CRYPTO_ECC_PRIVATE_KEY_CREATE...
Hi all,
When i walk-through the battery-service provided by nRF SDK, i note the presence of " Report Reference Descriptor " in the characteristic addition function.
I...
Hello,
I am trying to insert fds functionality to light switch client. I added all files and libraries to project. But when i try to compile project i face with errors...
