Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
As we all know that nRF52811 support AoA/AoD feature. But I have not found example in corresponding SDK( nRF5_SDK_15.3.0_59ac345 ) . If you have example of AoA/AoD,...
If you look at the secure bootloader example the nrf_bootloader_init(...) never return to main scope unless an error occurs.
Everything is handled inside this function even...
The " 5.3.6.8 Reset behavior " table in nRF52840 Product Specification v1.1 mentions that WDT reset does reset the WDT itself.
I'm trying to reconfigure the WDT after a...
Hello,
I am using HC-SR04 ultrasonic sensor and nrf52840dk. To measure the distance I have to find out for how long the ECHO pin of the sensor remains high.
for that I...
On my old Wondows10 development computer, all worked OK.
In a brand new Windows10 laptop, all up to this point installs/verifies fine using nRF Connect.
I cannot find...
Hello, I'm making a PCB project with nrf52832 and I want to use my debuggers only 2 pins(SWDCLK and SWDIO) to debug it. I have J-Link Edu, but I wonder if I can use it with...
Hi, All.
I' m studying nRF52832.
I have a question about example "ble_app_uart".
I m trying to send to smartphone using function "printf()".
Uart pins(RX, TX) are...
Hi everybody! I have a code running excellently on my nRF52840 DK. I would like to make it run on my nRF52840 dongle. What should I change in my SEGGER project? Can anybody...
I am building a project which requires accelerometer data from the LIS3DH accelerometer be read and then transmitted over bluetooth. I have successfully setup bluetooth transmission...
Hi,
For my project I need to receive 9 bytes of data from our main board. This data gets send using UART.
By looking at the pin diagram I could not find specific pins...
Hello,
I am running nRF Connect for Desktop v3.2.0 on Win10 64-bit machine. Everytime I launch an applet, such as Power Profiler, I get a new blank window and nothing happens...
Hi, I am having a problem changing information advertised by the Beacon while the application is running. I started with the app_ble_template example and added Information...
I have an nrf52832 dev board with me and I'm using nRF5_SDK_15.0.0_a53641a SDK version. I'm using the project " pca10040_ble " inside the " secure_bootloader " folder from...
Hello,
We are evaluating Thingy:91 for NB-IoT. We want to validate the RF transmit test and are using %XRFTEST command.
The syntax is as follows, AT%XRFTEST=1,1,3,18000...
