I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm trying to flash eddystone beacon example of SDK version 12.3.0 to this board ( https://www.robotics.org.za/image/cache/catalog/generic/NFR51822-MOD/NRF51822-MOD-000-650x350...
A step by step guide seems to be needed to get the asset_tracker sample application to use real GPS data from the nRF9160. I have tried:
1) Changing C:\nrf9160\ncs\nrf\applications...
Hi,
In SD_S132v7 chapter "Radio Notification", `Link-0 / Link-1 / ...` are mentioned several times, what's the meaning of that?
I mean, does it refer to a physical link...
Hi, team We have been experimenting with a system using Mesh for half a year. (The number of nodes is six.) The impression from the customer on the site we are installing...
Hi there,
We use nRF52832 to design a reader and use nRF52810 to design a tag. We put hundreds of tags together. Each tag transmits his ID every 5 seconds.
A reader...
BLE device(having nRF52832 chip) can not connect with mobile phone. for more information i have attach nRF Sniffer Log.
SDK: 14.2
Stack: S332_05_00_00 Multi protocol ...
It's my third installation on a (VB-) linux machine but the first one which didn't come to a successful end. The calling of "nrfjprog" works wheras the calling of "nrfjprog...
when I download softdevice and application use nrfgo studio,I can simulator by keil.
but when I download softdevice ,bootloader and application,I can't simulator by keil...
Hi All
We have an application using FDS, the SDK is: nRF5_SDK_15.3.0_59ac345 and the soft device is: s140_nrf52_6.1.1
There are 32 x 1024 byte FDS pages.
When the FDS...
I have SAADC configured in burst mode with 4x oversampling and tACQ=5uSec.
What is the total conversion period?
tACQ + tCONV*4 or (tACQ+tCONV)*4
In other words, is Sample...
Hello
Good day!
For example, if I have to use a Capacitive wheel sensor of 3 touchpads with the Csense example on SDK 16, do I have to configure 3 different output pins...
Hello,
I have an application to develop in which Central device is scanning with use of whitelist if it is not connected but have saved peers. If peer list is empty, device...
I have trouble when discover the BLE Peripheral that have the base UUID of characteristics and service are different. Then I followed several instructions in some cases, but...
I am trying to run the SDK15.3.0 gfx example code - only changing line 82 to:
And also I have changed the sdk_config to the display's width and height. I have wired it...
