Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello!
I'm trying to make the asset_tracker sample working on the nRF9160 DK. The at_client worked just fine and I was able to connect to the base station (I'm using NBiOT...
Hello, We have been using the PCA100059 version 1.0.0 dongle with a custom firmware which fails to run on the new PCA10059 version 1.2.0. Unfortunately there doesn't seem...
Hello,
Im a beginner in microcontrollers programming, just started with the pca10056 and pca10059. Im aiming to develop a beacon scanner for pca10059, to send data via usb...
I compiled and debugged the PCA10040e ANCS example (ie emulating the 52810 using the 52832) from SDK 15.3 - successfully. But I wanted to turn off code optimization to facilitate...
Hello,
As many mobiles do not have NFC I would like to use LESC OOB pairing with an QR-Code which could be shown on the device terminal. Well, I know where the NDEF message...
SDK version :15.2
question； when i use app_timer , i got interrupt which is not i wanted.
i creat and start timer :
app_timer_create(& m_timer ,APP_TIMER_MODE_REPEATED...
I'm using nRF SDK V15 with nrf52DK board, running the ble_app_hids_ms example.
I I want to have continuous non-stop advertising duration, should I have both APP_ADV_FAST_DURATION...
Dear Sir/Madam,
My question regards the behavior of the EasyDMA during the transfer of data to / from a serial peripheral like SPI or UART.
Let's suppose that during the...
Hi all,
I using SDK 15.1 and 15.3 for test.
I am working with DFU for NRF52810.
I tried success for NRF52840.
But I can't update success for NRF52810.
Below is scrip...
I use the Firmware «AT host sample» on Thingy91. Then I connect to Swisscom network on band 20. The current consumption is about 3.5mA. Then I send AT+CFUN=0 or AT+CFUN=4...
Hi All
We are using nRF9160 DK, and we are working on ADC channel. we use This example of ADC. I am using single-ended with no over-sampling with a gain of 1/6, reference...
Hello
my setup is sdk 15.3, nrf52840, s140, open bootloader and an application.
Everything is merged, flashed and running and no changes are made at the standard addresses...
I am currently developing a peripheral app on a custom board with a nrf52832 chip on it and connecting to the device using QT's ble library. I'm having issues where my connection...
