Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello
We try to measure package loss if BLE Advertising & BLE Mesh is used in a congested environment. (WLAN accesspoint has MIMO, 18dBm, heavy data transmitting with psping...
Hello Everyone,
I am using nRF52 DK and i have 2 SPI slaves (ADC and EEPROM). ADC works with SPI mode 1 and EEPROM works with SPI mode 0.
I figured that i need to manually...
Hello Nordic, I've been searching the forum and the SDK for code examples that specifically use Bluetooth 5; could you direct me to that code? Many thanks in advance for your...
I am now based on nrf52832 SDK14.2 development, I tried to use the PWM driver and timer to drive the corresponding two IO port an irregular waveform, I originally thought...
I am using the Hackable kit which has nrf52832 to control a servo motor and read accelerometer(AXL335) readings through a iOS app. I am a novice when comes to embedded. I...
Hello, ererybody!
I use nRF52832,have a development board.
I was testing the adc module,using the ANI2 channel,I measured the ANI2 channel voltage to the ground,find it...
Hello everyone,
now i'm working with nRF52840 PDK( Engineering B ) and i migrate my project from SDK 14.1 to SDK 15. My starting point is ble_app_template and i want to...
Hi!
My setup:
* nRF52 DK (let's name it N )
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* two android smartphones (let's name them A1 and...
1. nrf51822-qfaa
2. sdk10.0 & sd8.00
Q:
If the MAX_CONN_INTERVAL is set to greater than 200, NRF_ERROR_INVALID_PARAM will be returned when called sd_ble_gap_ppcp_set...
This post had a discussion on using one button but the first reply suggested a buttonless solution. So now I'm not sure if one button dfu is best if same button is used for...
hi,
i am doing a project where i have to exchange strings between nrf52832 as peripheral and andoird smartphone using nrf connect app, in this project data security is a...
Hello!
It's the first time using Nordic devices so i´m doing some SDK examples and trying to merge them. I'm using SEGGER Embedded Studio. Right now i´m using ble_app_blinky...
Hello,
I'm usign nRF52832 IC and SDK5. I want to awake the sleeping MCU by NFC and pair with BLE. In short Pairing device address should be transfer via NFC. There will...
Hi all
i am using SDK15, nrf52832 dev kit and s132 version 5
I followed the below steps:
1)Flash the softdevice
2)Update the generated dfu_public_key in secure_bootloader_dfu...
