I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
hi guys,
Can you please tell me what is happening when a smart phone trying to connect to nrf51822? Any event I could use? Would the connecting process has any impact on...
Hi,
I've just got my hands on this amazing little thing call Thingy 52. I have played around with the default app but now I'm struggling with flashing a custom firmware...
Hello,
I am trying to setup two Thingys with my node-red system and i have ran into some problems. The thingys respond to normal command line tools like gatttool, btmgmt...
Hi All,
I am new to Nordic microcontrollers. I am using keil uvision MDK lite version. After I have uploaded a source code and when i am trying to compile. I am getting...
Hello,
I am starting a new thread concerning the two messages that I have posted about generating a 4MHz clock on nRF52832. I am using the nRF5_SDK_14.2.0_17b948a SDK. ...
Hi,
if I correct understood DFU process first of all it need to send "Init packet" and after that it need to send FW image. And for that reason in DFU packages is 3 files...
Sir, i am looking to design customized board using nrf52832, i have pca10040 borad as well. i am looking for eagle library of antenna used in pca10040 (i.e nrR52DK).
if...
Hi, I'm trying to program a nRF52-DK, with a workong firmware, and a board that was working, but I can't manage to flash the DK.
With a make flash_softdevice:
Flashing...
I am working on nrf52832 BLE. I have used soft device s132. Antenna device is as per the reference design of NRF52832 and have used 32MHZ crystal for HFXO oscillator. but...
I am starting analysis for project of BLE Central device that is only receive broadcasting packet (advertise) from peripherals.
However, it’s unclear to me. I doubt will...
I notice that the sensitivity for the nRF52832 is defined as being ~2dB better in BLE mode than in NRF mode. I have also tested this to be correct.
However, I wonder - is...
Hi!
We have several products which use SoftDevice S110, some of them are already in production and are listed as Bluetooth Qualified, some of them we are preparing for production...
I've a custom board that uses a nrf52832 and Li-SOCl2 battery (3.7V). We've programmed several boards with our firmware and kept then with BLE advertisings every 300ms. A...
I am trying to develop a simple SPI master for a custom nRF52832 uC, but I can't find anny sort of sample codes that don't use Soft devices for this task. I need the code...
