I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I have known your board support jlink ob；I want to debug through it ;
I want to know if i need to buy the software-license from SEGGER ？
and if i need buy the software...
Now facing the problem "After disconnected, the electric current increases"...
I think softdevice is working hard even after disconnected when connecting once.
Could you...
Hi,
I'm trying to write unit tests and have arrived at the point to write tests for ble characteristic addition to a service.
To offer some background, I have written...
Hello,
I use NRF51822 and I try to output UART message onto hyperterminal program.
but every message I send it contains "APP:INFO:" in front of the message.
like...
I want to use nRF Connect v2.1.0 to debug.
But i faild to connect the correct J-link because the nRF Connect choose the wrong J-Link IDs on the COM. So i can just change...
I'd like to use nRFConnect with a direct USB/Serial connection to my nRF52832-based device. I've read that it currently checks the jLink chip.
Is there any way to configure...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
for multilink client services Nordic introduced the *_EVT_DISCOVERY_COMPLETE events and the *_c_handles_assign functions. Like the BLE_BAS_C_EVT_DISCOVERY_COMPLETE...
Hey
Would 3++ nRF51822 bluetooth smart beacon Kit sense in location application where lets say 2 beacons are quite close by (half meter) and third, the locatable beacon...
Hello,
I have modified my device name (nRF52, BLE) per the function below. When flashed to a board, I then use nRF connect to look for this device.
Using Windows nRFConnect...
I'm having an issue when trying to perform sequential reads with the ADC on 4 different pins. I've setup a timer to trigger every 1 second. In the Timer0 IRQ I setup the ADC...
Using SDK v12.2.0 . Starting a new project with Segger Embedded Studio, I have to assemble an sdk_config.h file. For example when using GPIOTE I first need to find an example...
Hi,
I am using ble mesh sdk 0.9.2 light control sample where I have modified it to send messages from the client to one particular server every 5 seconds.
Now I am trying...
Hello, I've got an nRF52832 on a custom board and I am unable to perform an SAADC calibration correctly.
I'm using SDK14, SD212 v4.0.2., and my main application code broadcasts...
