I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I am using nRF 52 DK with Softdevice s132 v4.0.2 and app ble_app_uart from sdk 13.0.0
When i try to connect using nRF Toobox running from my Nexus 6p Android phone Segger...
Hi all!
I write for nRF52 but I can't to understand it. There are two cases:
first- I want bound my peripherial with central. And in future I want connect only between...
Hello iam using softdevice 110 and SDK 10.0.0, I have created project using ble_app_uart example code, i have added device manager APIs to manage bonding. Problem is iam GATT...
Basically, it can be divided into two cases
Reading/sampling TX pin of the sensor (since usually nothing is sended back)
Send/Read possibility - in case of range switching...
Hi all, today I was working properly and, in a second my nRF52382 (I use SD s132 V3.0 without bootloader, and SDK 12.2) is "disappeared". I googled and I've found some cases...
I am using nrf51822 with 16k RAM chip, xAA.
I followed the procedures...but I don't know what is wrong with it..
Program secure bootloader with S130 (2.0.0), SDK...
Hello,
I am trying to use the new nRF Connect 2 for Desktop. After installation, the app gets stuck and doesn't show any GUI. Investigating the network shows that the app...
I have been setting up systems to develop nRF52 code for the better part of two years. Maybe I am getting forgetful in my old age, but I can't seem to get it working this...
Hi.
I am looking for appropriate 2.4Ghz Nordic RF chipset.
I have studied 2.4Ghz chipset. but so clearly show about
1:n audio streaming (mono or studio)
exactly what we...
Hi, we are using nrf51822 xxAB based module and would like to understand which SD/SDK combination is best to use in terms of memory usage. We have developed original firmware...
I'm in the process of migrating from SDK11 to SDK13. I have a custom UUID with 3 characteristics (2 notify chars for data and 1 r/w for sending commands), based off HRS and...
Using SDK 12.1.0
I2C with SoftDevice works on PCA10040 Eval Board with nRF52832 but
hangs in the nrf_drv_twi_enable function with TY module EBSGCNZWY which is an
nRF51822...
Attached program has 4 characteristics
UUID_VLEN1 - VLOC_STACK, no rd_auth or wr_auth - value can be read after written
UUID_VLEN2 - VLOC_USER, no rd_auth...
Hi guys,
I'm receiving the following errors whilst trying to setup to the Crypto library on nRF52:
............\components\libraries\svc\nrf_svc_function.h(72): error...
