Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I have been trying nrf-sniffer with no success. Setup is:
Win7 64,
Sniffer Win 1.0.1,
Wireshark 1.10.14 (both win32 and 64 tried),
PCA10000 and PCA10001
The sniffer...
I generally upload codes from mbed.org to my PC then send the hex file to nRF51822 by nRF51-DK's pins. But I don't want to use cables to upload hex codes to nRF51822. Are...
Hi community,
When I want to use the example multilink peripheral inside the s120 directory example of the SDK 6.1.0, I'm not able to compile the code.
The device_manager_peripheral...
So, I want to make an application where my NRF52 advertises an URL via the Eddystone beacon.
The URL will link to an webpage, that will connect to my device through the physical...
As here said link1 If we want to use flash in the mesh we should ignore APP_ERROR_CHECK(NRF_ERROR_INVALID_STATE) in ts_sd_event_handler() ,
2.And here link2 tell us...
How do I set up a variable length characteristic which is greater than 20 bytes and use notifications with this characteristic?
For example I have several variable length...
In an nRF51-based application I'm working on, I am using the SPIS peripheral and a generated clock signal to send a large buffer out over serial using DMA. I want to use the...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
hi
in tutoriall service beginer there is
static void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;
// Build advertising data struct to pass...
wireshark 2.0.3 which is what got installed when I downloaded it is not supported according to the nFsniffer program.
So what, and how do you set this up?
I am using a function to read the die temperature data from nRF51822 as follows:
static uint32_t temperature_data_get(void)
{
int32_t temp;
uint32_t err_code;
...
Hi all,
my Setup :
nrf51822 QFAC Build Code A1,Waveshare Core51822 Board
keil microvision
nrf device family Pack 8.6
without Softdevice erased with openocd...
Was testing DFU Failures scenarios on SDK 10 to make sure that the software elegantly handles when an Image fails to transfer/swap/load/disconnect..etc. I find that when an...
Using adafruit sniffer. Windows 7 32 bit professional, windows 7 64 bit professional.
After installing the FTD drivers I see com5 installed.
when I start the sniffer it...
