I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi, I am trying to generate PWM pulse based on sample application in GitHub. However instead of using different modes and multiple channels, I tried to simplify it to just...
Probably a silly question, but I am new to Nordic Semiconductor and can't figure this out. I am trying to make a new project based on the Template example for nrf51422_xxac_s100...
I am writing my own function to setup a notification characteristic, but it failed,
Could anyone help me check it ?
static uint8_t d[2] = {0};
static ble_gatts_char_handles_t...
I have been experimenting with mbed ble programming and have had some success with the examples and my own programs. Everything works fine on the nRF51 dongle and DK.
I...
I'm trying to enable the active signal for an nRF8001 on Adafruit's breakout board. Is there a way to do this without using the nRFgo software? I use a Mac so setting up nRFgo...
Hello.
I use BLE Shield V.2.1 of RedBearLab.com for Arduino.
The shield equipped nRF8001.
After about 62ms from reset nRF8001 by putting Low signal in Arduino pin 4...
Iam using NRF8001 in my project & i don't know how to enable them & connect them through Android app basically iam using in tracking chip so any one have a idea that how to...
I am using an Arduino and NRF8001 break out board from Adafruit. I am using the UART profile (adafruit sample code) to send data between mobile phone and Arduino. However...
Hi,
I am trying to setup the nrf8001 by sending the setup commands from my microcontroller. After I send the complete setup packet (21 commands) I receive, as expected...
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02", which...
After a fresh install of Keil (along with Legacy patches) and the SDK, I get the following messages when I try to open the ble_app_template_s110 project:
The project...
Hi All,
I use iot_ipv6_udp_client example on nRF51 DK.
I modified it and send data in one direction only (not receiving back).
Testing has shown that the maximum packet...
Hello,
I use S130 with NUS style connections as central and device at same time. It works nice and performance is good but when i run scan, performance become very poor...
Hi,
I'm using S130 with SDK 9.0.0 and as central, I'd like to read values for more than one characteristic on a peripheral. I do so in BLE_GATTC_EVT_CHAR_DISC_RSP by firing...
