Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi... I am using 15.2 version sdk , i have merged ble_app_uart and twi_sensor example code . complied successfully but while running after two output data i am getting fatal...
Hi,
I successfully added libuarte async library to the ble_app_uart example. Now I am able to receive data over UART from another board and my goal is to transfer it to...
While still trying to debug the disconnect problem in a different thread (unsuccessfully), I've gone to the ATT_MTU_THOUGHPUT example, to try and understand it and gain more...
Hi,
I am working with a custom board with a third party NRF52832 module. On my board I have a DS3231M real time clock IC communicating with the NRF52832 via I2C/TWI and...
I am trying to have a bluetooth bond between the device and the app,
how to set a security key to bond it with the android app? and also can I know how to encrypt all the...
Hi,
I have a question about getting the appkey from flash:
I am using the device state manager for key management. I do a ramdom generation of netkey and appkey on first...
I have a few different Fanstel Eval boards that contain the nRF52840 SoC - starting with the BT840XE. I'm able to flash the board with example firmware and my own custom firmware...
Been working on an unsoldered, untinkered, and in all ways untainted nRF5340-PDK. No jumpers changes. No solderbridges cut. All working fine, but all of the sudden I cannot...
Hi! I want to program a custom BLE application (as Central/master/GATT client device) to run on a Windows PC using a nRF51 Dongle (PCA10031 board) attached through USB in...
Hi,
I am working on the software development of a product based on an nRF52832.
We began our development on the nrf52810 and then moved on to the nRF52832 as it became...
Hello,
I'm struggling to connect to an MQTT-SN Gateway when the device is configured for low power. Currently using MAC-OS Catalina 10.15.3, SES version 4.42 and have tried...
I tried to install the nRF Connect SDK v1.3.0-rc1 error
I open git-bash.exe to execute the ncsmgr init-ncs command, the following error occurred during the installation...
nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager
I am trying to install nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager using nRF...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...