I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hello I just got nrf52dk board, and have issues with dfu mode of MCU, after power on board is dead no any lights, no USB connection. After pushing reset and power on, MCU...
Hello,
I am implementing an application, where I want to connect three NUS peripherals to one NUS client. As a beginning point, I started with the supplied examples from...
I have ported the keyboard example code and integrated it with another set of services. However I don't see the device responding to an LL_ENC_REQ. I'm not sure what I can...
This probably falls under the category of BLE Basics, but I'm a bit slow and need some help. Here's my scenario:
I'm building a very simple BLE Peripheral that provides...
I'm currently using nrf8001 to send data to my phone. To save power from the peripheral device, I wanted to change the connection parameters.
I set the min and max connection...
Hi, I'm using nRF52832 with my external board.
I'm recently working ble uart example.
I control motions with tx message such as LED, motor and so on.
Now, I want to...
Hi,
I need to set a client back to the state, when its flash was erased and programed, so if I understand this correctly, the provisioning data has to be erased.
How could...
I've been developing on the PCA10028 development kit with print statements working fine (though at the moment it seems only SEGGER_RTT print statements are working and not...
Hello,
I am getting an error message while I was compiling the "ble_nfc_pairing_reference" example. How can I obtain this " micro_ecc_lib_nrf52.a" file ?
Fatal Error...
Hi,
I'm trying to edit the nfc message in software but after a while the nfc stops working.
What could I be doing wrong? This is my code, I change the value every second...
I have a project that I assume was originally set up with SES on Windows. I need to build it with MacOS but I get an error 'sdk_errors.h file not found.' I assume this is...
Hi,
I finally want to integrate BLE and 2.4G in nRF52810.
【1】I am studying Timeslot,i found some articles in DevZone.
There is a mention of micro-ESB , so what is micro...
Hi, I am currently testing some BLE sample code (the proximity code and hrs code) with the nRF52840 PDK and I am trying to just simply interface the GPIO interrupt example...
1. How should I connect with UART to my board?
2. How to put the device into RX mode as required by RED EN300328?
Test the Radio Test Example application by performing...