I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
can't program nrf52832ciaa
I can connect the core through segger commander
I can erase the chip after push the download bottom in the keil 5 ,and erase the chip...
I have an nRF5- DK and I'm following this tutorial . I loaded the softdevice, I can compile, I can load the flash, I can see the output in Termite, I can change the code to...
Hello,
I have an NRF51822 custom board. I am trying to flash the code under
C:\Users\Home\Desktop\nrf51\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart...
Greetings -
The (custom) device I'm working on has multiple possible serial interfaces. I thought "Hey, I've written entire operating systems before, I should just intercept...
Hi all,
i need to write in flash, and i try to use the example flash write of sdk. It works correctly but when i put it in my code, the writing register ( NRF_NVMC->CONFIG...
Hi!
I'm developing Thread mesh using nrf52840 with COAP communication. I would like to set a longer timeout and more retransmission tries in COAP. I saw this parameters in...
I am trying to use one of the example from NRF5 IoT SDK with RPi3 (kernel 4.9.41-v7+) but keep getting "permission denied" when execute command below:
echo "connect 00...
Hello
I have setup my Eclipse(neon3) on Linux following the instructions in devzone.nordicsemi.com/.../7
I cant compile and flash the image. But cant breakpoint.
I...
I've read that the number of tx buffers on the S110 is fixed at 6, however I've also read that this may be configurable on future versions of the softdevice ( devzone.nordicsemi...
Hi,
I'm currently in the process of integrating unit testing into our firmware development process. I'm trying to execute on-target tests with the Unity test framework...
Hi Nordic Semiconductor, I am Yoganathan Sivakumar studying Master in System on chip in LUND University. I wanted to ask some technical question in industry oriented. I wanted...
Hi,
Recently I receive the "nRF52840-Preview-DK" and I download the "nRF5 SDK v14.0.0".
I try some example with Keil and all of them works well when I use the MCU interface...
I have a strange bug, that I do not have any good answer for.
In the software, I use either SPI1 or SPIS depending on current configuration, I have seen some rare cases...
I know it's not very common to use a secondary service, but I want to use it in one specific scenario. When referring to the documentation for the API sd_ble_gatts_include_add...
