Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Dear Nordic Support Team,
I am trying to write some information in the flash memory without success. In the ble_flash.h file, it is specified that the pages 0-127 are reserved...
hiii....
1.can any one tell where do we call advertising_start() function if we want to advertise after getting disconnect from a central device.
2.in ble_evt_dispatch...
I`m a newbie at Bluetooth Low Energy and Nordic Chips. I bought a DK for the nRF51822. I would like to set I/O pins over android and iOS application.
1.So what application...
Are there any common solutions to the issue of spi_slave.c using an array as its buffer? I would like to setup a circular FIFO, but I am not sure if there is any way to do...
We are using the S110 as a peripheral that emits data via notifications.
Is it safe for the central to also send characteristic writes while notifications are being emitted...
First of all ,i download the SD7.0 to my device, then i download my app to my device,in this case
my device's curent is 100uA.
First of all ,i download the SD7.0 to my device...
Hello,
i need some informatiorn about the layout of the nRFgo Motherboard. More specific i want to build a board which is connected to the ports P0, P1, P2; therefore i...
I'm trying to implement a burst transfer between to nRF24AP2 devices, but I have serious problems getting it to work.
The burst messages are send on a reverse channel to...
Hi, I need to read an analog signal 100 s/s which takes 68us at 10bit. There is very little computation to be done once read probably about 10us which I can do to the previous...
I am experimenting with calling sd_flash_write with waiting,
if it returns NRF_ERROR_BUSY, just try again, and then return either success fail
void flashWrite( uint8_t...
Hey ho,
I'm new to BLE and Nordic. I'm a student from Germany and i want to realize one simple function with Arduino (RedBear Blend with nRF8001) and Android.
I want my...
Hello,
We've heard that the BLE transmission packet length may be increased beyond the limit of 20 bytes in a future version of the S110 softdevice. Would you let us know...
Hi
I struggle to understand mechanisms of switching particular subsystem of nrf51822 off and on again in order to consume as little as possible current when MCU is put...