Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hello. I'm using 24 MHz crystal to feed my MCU and not able to change it to 16 MHz to share with nrf24. Now I'm driving nrf24 XC1 with PWM signal 16 MHz and it works but not...
Hi,
We have NRF51822 chips programmed for specific application and it is working fine as BLE services etc.
In some scenarios, to debug we want to stream data from our...
device_manager_peripheral.c provided via Software Packs in Keil doesn't compile against S110 8.0.0 (or 8.1.0). Its version shows up as 1.1.1. Same thing happens with bsp.h...
By combining some examples, I'm starting to understand how the UART examples works.
Using Keil 8.0.0, and the PCA10003 Board, I'm trying to send a burst of messages over...
I can see and bond nrf51 with android, but with iPhone nothing.
What can i implement for see nrf51 with iPhone?
Can i pair Iphone and nrf51?
Sorry for the very bad english...
The new generation of nRF51822's have a few neat new features, particularly the automatic power management piece, that I would like to potentially leverage in our project...
Hello,
I'm seeing some 67.2kHz reference spurs on the RF signal when I'm turning on the constant carrier mode using the DTM interface on the nRF51822. Layout and circuit...
Two applications using the same softdevice, s110, blinky and beacon from the examples.
Flashing softdevice and beacon successfully.
Replacing beacon app by blinky successfully...
The bootloader in SDK 8.1.0 (at /nRF51_SDK_8.1.0 examples/dfu/bootloader) calls pstorate_register() twice. The first time as part of bootloader_init(), then on bootloader_dfu_start...
hi,
I have implemented a UART to receive network packets from another controller to send it over BLE.
UART config are: 8bits data, 9600 baud rate, no parity, HW flow...
Hello,
I am wondering wether I need to pass regulatory tests when I use the S130 Softdevice together with a 3rd party module such as the one offered by raytac ( www.raytac...
Hi,
So i don't have any experience of working with nrf ble chips, but i was given nrf52 DK and i need to make it work as an iBeacon. So i got the dev board working without...
I'm planning to implement a mesh network, where each node (ble device) also acts as a scanner, detecting BLE advertise messages. The mesh network would then forward the advertisement...
