Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello
Just few quick questions. What happens to the S110 Softdevice after the APP_ADV_TIMEOUT_IN_SECONDS period?
I'm using the nRF51 DK and the ble UART example and I...
As I am using nRF51422 EK (Evaluation kit), would like to know how to test with BT2.5 or lower version. Is this has backward compatibility. As when I give option of FLAG other...
Hello
I'm having difficulty in executing an GPIOTE interrupt during a BLE connection event with the nRF51 DK. The interrupt I have works fine when the softdevice is advertising...
If I set the centrals connection intervals values higher as a specific value it won't any longer find/connect/enable notifications on my peripheral.
0x00A0/0x0050/ 400...
After running the advertising_start () function in the sample software.
I set the breakpoint by Keil MDK-ARM v5 and stopped executing.
Afterwards, reset is generated!!
...
Hi,
I am using a gpiote interrupte handle function to send a notification to the master,but I find when the sd_ble_gatts_hvx() function is used,the interrupte handle function...
I have successfully completed dfu using android app, but if anyone can help me with example program so that i can perform dfu using program instead of using toolbox app, please...
On the XLR2 chipset I am seeing that if the RTS output follows the state of the CTS input.
When I load the same firmware in a XLR then RTS does not follow CTS
Hi, I am evaluating the use of ESB(without Ack) and BLE as a possible solution for my project since i have no use of Ack and in Gazell it is mandatory to use Ack. I had heard...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I'm drawing schematic with nRF51822 internal LDO. I'm wondering what is the regulated LDO output from nRF51822. I need to connect that with peripherals in stable...
We are using ANT with the nRFgo motherboard as base station and want to broadcast a signal over the largest range possible (> 100 m) to several mobile devices using the Dynastream...
I am designing a ECG monitor device. The data rate is less than 50kbps. I was planning to use BLE for the device design. But I read some documents that say BT classic is a...
Hello,
My 10031 dongle worked perfectly up to the point where I flashed it using MCP. I was able to run simple programs such as blinky, but now I cannot revert to the previous...
