Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I'm trying to update my SoftDevice with a bootloader, which is basically the same as the one in nRF5_SDK_11.0.0_89a8197. The image is saved in bank 0 and is validated by dfu_sd_image_validate...
This is my first DFU project, and so this may be super-obvious to all of you.
I am writing this here to help others, because it appears that there are others out there...
I have an mBed application that uses the S130 SoftDevice and polls data from a couple of other connected peripherals via I2C & SPI.
I use a Ticker object, which seems to...
Hello,
I use the example dfu_dual_bank_ble_132 in the nrf5x sdk 11 (PCA10040).
I have had my programe before the OTA, i will have a programme wich would update at any...
Hi all:
I stored some settings in flash in the address 0x00077000 and this address is got by the function of pstorage_register().
However this area will be erased by...
Hello there,
I've been trying to use embitz (the new version of emblocks) to program a nRF5188 but i always fail to compile the "ble_peripheral_hrs" exemple, i'm always...
Hi
I have a unit that is rather old and I want o update it to the latest softdevice.
In the unit there is a bootloader and softdevice version 6. Does anybody know if it...
I'm making progress, but still struggling to get the sample DFU built into NRF Toolbox to download successfully with my bootloader. Using hrs_dfu_s130_*.zip.
For this,...
I tried if there is a possibility that my device would brick if I interrupt the DFU process. notice that I'm using SDK10 with dual bank bootloader. I uploaded the app over...
I am going to develop on nrf51822 and the data sheet says nrf51822 is s110.
I want to load an example of sdk 11 but there is no example for s110.
I am a total newbie, so...
On the nRF52, does the TASKS_HFCLKSTART need to be trigger again after waking up from sleep, if the the HFXO was started before going to sleep? Or does the Clock control circuitry...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I have one characteristic which send data with indications, for each frame sent I wait for acknowledgement on case BLE_GATTS_EVT_HVC : before sending the next data
but...
I write a source code to test led and button driver. it's work with a loop but when add sd_app_evt_wait() to use low power mode of nRF52.
I suppose that I forgot something...
Hello,
i have one problem.i am working on the TWI using Handler.it is working.
but i have very strange issue regarding to the dereference the value.
please check in...
