Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi, I found the example of Eddystone beacon in SDK 12, but couldn't find Eddystone Configuration Service demostrated or implemented. In the legacy nrf5-sdk-for-eddystone repository...
the mcu is nrf51822，I use sdk9.0,
sdk9.0\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5_no_packs
In this project, I delete led，button，
change “dfu_start...
I use it. nRF52832 PCA10040 Vesion12.2.0
I am working on the ble_app_uart example as a base.
I used the sd_ble_gap_addr_set command to change the BLE address but it...
Since Google released Android Marshmallow 6.0 we are experiencing problems when connecting our nRF51822 based peripherals to a Nexus 6 phone.
The Nexus 6 is able to see our...
I use it. nRF52832 PCA10040
I have coded based on NUS.
However, I failed to pair with my Android device.
Even with ble_app_uart, the result is the same.
Hi. I'm using SDK12.2.0, S130 ver2.0.1, nRF51822AC as central.
After connection, if i use "ble_conn_state_n_centrals" function, i can get the number of connected peripherals...
my ble can send data when the data send function called inside main.c ,
But it is not sending data other than in main.c like other source files.. and getting error invalid...
I'm trying out different SDK's and some of them are working to an extent (they load the softdevice, and the app, but when I test run in debug they start at a different location...
I am working with the nRF52832 pca10040 devkit, and when I program the softdevice with the nRFgo studio, the only version that shows the firmware after programming is S132_nRF52_2...
Hi,
we are using nRF51822-QFAA in our project which is based on the PCA10000-nRF51822 Development Dongle 2.0 - layout of radio part is almost the same. I'm also using sdk...
I need to read variable length blocks from an I2C slave using a TXRX transfer. The length of the following data is given in the first read data byte, similar to SMbus Is there...
I installed Bluetooth Developer Studio , (BDS), which appears to offer a way of setting up a custom profile without have to spend too much time on writing low level code....
