Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I am trying develop a project in which when we request a characteristic from phone( read request), we will read data from other module through UART and give reply back. I...
Hi,
I designed before my board for 2 layer PCB and i used the coplanar waveguide with ground-plane in the bottom. now i want to move to the 4 PCB layer and i choose the...
Hi, I'm porting my project from SDK8.1 to SDK10.
I replace static app_timer_id_t m_beacon_timer_id; to APP_TIMER_DEF(m_beacon_timer_id);
to avoid hardfault when creat...
Hi all:
I modified DFU-BLE to make it suitable for S130 on nRF51822. I made the following modifications:
On "dfu-ctr1_pt_add"
ble_gatts_attr_md_t cccd_md;
memset...
Hello!
Until now I am using a nRF24L01 with johanson balun (2450BM14A0002) and MIFA.
I want to add a power amplifier to my nRF24L01 project. Can anyone give me advice which...
Hi
I have a programming issue with nRF51822. I am using the nrfjprog.dll to program this microcontroller in my test equipment via J-link Plus. When I have programmed a...
I am using single NRF24LU1P-F32Q32-T ic.i am using it only as a TAG transponder card .i wanted to know that can we program it to transmit only if there is no other controller...
hello everybody,
I measured the current consumption in two cases : in the advertising mode the current is around 4 ~ 5uA, & in the connected mode, the current is 160 uA...
Hi,
I am new to forum and to Ble. sorry about my week English.
I am working on a project where I am reading adc value every 1s and sending it over ble. So I have written...
Hi,
I'm using nRF dev kit with Softdevice 1.0.0.3.alpha. The device shows advertising state at LED1 as it should, however i can't detect "Nordic_UART" via nRF Master Control...
Is the advertising interval between two packets P1 and P2 defined as:
Interval = P2_start - P1_stop (time between packets)
or
Interval = P2_start - P1_start (time...
