Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi,
I have some problems with the example 'timer' and 'simple_timer' provided with sdk_15.3 (which are explained in my other ticket). So can I have an example which works...
what exactly ble_beacon stack is used for? what it does and can it be used to advertise or send user data (like string) and receive notifications from other devices ...can...
Im struck at some point with some error, added all supporting file along with header files but still im getting error. Im using sdk15.3 pca10040 nrf52832.
please verify...
I have a NRF51 DK board, and can't get it to do anything with BLE (probably including any of the examples that require a softdevice) but I ran the blinky examples just fine...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. It is placed on a custom board such that all pins from the nrf52 SoC are brought...
Hi,
My projects with Nordic chips thus far have been pretty simple, but now I would like to use an RTOS. My question is, do I use the FreeRTOS available in nRF SDK, or move...
Hi,
I have a problem with understanding, how bits in ble_gatt_char_props_t are related with Specification of the Bluetooth System v5.1 Table 3.5: Characteristic Properties...
If I use a breakaway for some debug pads which SWDIO and SWDCLK are connected to and then snap it off so the traces are no longer connected to anything, will this cause a...
I'm trying to run the https://github.com/NordicPlayground/nRF52-ble-long-range-demo on Fanstel modules with integrated AFE by Skyworks - BT840X(E) https://www.fanstel.com...
I'm trying to connect to an AWS MQTT broker I have set up based on the code in https://github.com/joakimtoe/fw-nrfconnect-nrf/tree/36532a8ca60bf7139a988b5cbb4e6cb47948a9fa...
Hello In this thread we discussed a possability of building a system with large number of conecctions. So, we need to get data from 30 peripheral nodes on one central host...
Hi,
I'm developing a product that should take an image of a low-resolution image sensor, process it and send the result via BLE.
The camera has an 8-bit parallel interface...
Hello, I was finally able to connect the board via LTE to my nRFCloud account. However, when I go through the getting started guide, specifically the programming a sample...
Hi
Now I use the SDK15.2+MESH3.10 build my project.
Because my firmware was very large.
Moreover I want to use the nRF Connect update my device.
So,how to integrating...
HI I started off to test all the drivers before the actual development process kickstarts.I tried using the TWI sensor example for an i2c driver check.I used a DS1307 simple...
