Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I just recently upgraded to SDK 7.2.0 and am now using the keil pack installer as well. First of all, I really appreciate the ease of this new system, but I'm running into...
The new softdevice v8 states that previous revisions(1 and 2) don't support all the new features, and I'm curious how to determine what revision my ic is.
thanks,
akbar
Hi
I have recently purchased an Adafruit Bluefruit LE board ( www.adafruit.com/.../1697) , that uses the nRF8001 chip, so that I would be able to send iOS notifications...
I have a new nRF51822 kit, and although I can (apparently) configure the beacon, it always shows "Beacon not found" when I try to use it.
I'm using an iPhone 5s and the...
Hi, I got new NRF51-DK and dongle with 51422 chip.
It seems that the layout of the memory map has changed with the new SDK and I can't find any information how it should...
After I uploaded hex and dat file which is compiled from sample beacon source code in SDK to nRF51822 Beacon Kit via nRF master control panel app, I got Upload failed GATT...
I have done some testing and debugging, but I can't seem to get the nRF51 DK working with the beacon example project.
I used the keil v5 pack installer to access the ble_app_beacon_s110_pca10028...
I've noticed that the L2 value has been changed from 10nH to 27nH in the reference layout and on the new boards (DK and Dongle). This value is only for LDO setup (from PS...
Hi,
If we set the prescalar for RTC1 to 0xFFF (i.e. max value allowed), tick event is getting generated every 125msec.
Using the below configuration i started a timer...
we use the dfu_dual_bank_ble example as our boot loader. We are currently using an 81522 AA part and the boot loader works well.We have recently moved to the 81522AC part...
I have been trying to get the SPI Slave to work on an NRF51-DK for about a day now and I haven't been making any progress.
I first tried it with the softdevice enabled...
Hi,
I'm designing a wearable, low power inertial and EMG system and have to choose between using ANT+ or BLE with the Nrf51422 on my own board.
The system would simply...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
