Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi Because I have a custom board with the nRF91 module, there is no possibility to send data to nRF cloud, because it works only with DK boards. I would like to send asset...
I want to use this sample application, to connect with nRF52832 DK loaded with Running Speed and Cadence Application. In other words I want to use nRF9160 as a gateway for...
Hello all,
my compiler can't find the definition to timer functions : nrf_drv_timer_init(), nrf_drv_timer_extended_compare() and nrf_drv_timer_enable(). bellow my code :...
I am using Nordic nRF52832 Development kit . I want to interface Load Cell with the Development kit. Which examples in SDK i should refer to get started with Load Measurement...
Hello ,
i am facing some issues regarding nrf mesh uart example.i am using nrf52 sdk and trying to use uart for my project to send a data to a particular node in a group...
Hello All,
I am trying to merge the "secure_bootloader_s132" and "ble_proximity" examples.
I have combined all file .
(Here i am using Segger embedded studio with nRF52...
Based on the mesh sdk3.1 operation dfu, according to the operation instructions, dfu_mesh.zip cannot be generated.
nrfutil dfu genpkg --hlep Found no parameters for mesh...
Hello everyone,
A nRF52832 with SDK 15.0 was used for my application. I am trying to send a large amount of data via BLE with a custom BLE service. I extended MTU size so...
Hi
I have been developing a 'custom' firmware to be used in a nrf52 based device. The idea is to replace the original firmaware (too limited) and burn my own.
Hence, I...
FYI,
the auto-update fails for version 2.7.0 of 'nRF Connect for Desktop’ with the attached error dialog.
I had to manually download it again from the link below, and...
When I am trying to run my code in nrf52840 DK board, the program halts in a specific PC and does not go forward (2nd image).
I am using SDK version 14.0.0 and softdevice...
i opened the example of ble_app_uart_c in \examples\ble_central\ble_app_uart_c\pca10056\s140\arm5_no_packs in <nRF5_SDK_for_Thread_and_Zigbee_v3.1.0>
and i haven't changed...
Hi!
I have been following this process to develop using armgcc and Eclipse: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/development-with-gcc-and-eclipse...
everyone, i have a problem whit 51822. nRF5_SDK_12.3.0_d7731ad
i measure time from 51822 poweron to main .
if i only softdevice and app code, time is only 4-5ms only....
Hi,
I have a question about parent.
Firstly, make topogoy as belows.
ZC --- ZR --- ZED
In this situation ZED's parent is ZR. correct ?
Let ZED's ERASE_PERSISTENT_CONFIG...
